Is any Trimming Required To Install The etrailer Trailer Hitch Receiver On a 2023 Hyundai Palisade?

Question

Question:

Will Installing the etrailer hitch require any trimming or cutting on my 2023 Hyundai Palisade?

asked by: Pete M

0

Expert Reply:

To install the etrailer Trailer Hitch Receiver # e95ZR on your 2023 Hyundai Palisade you will have to do some trimming. This is going to be needed on the underbody panel which attaches to your frame so it will not be seen. I have linked an installation video from an install we did in our shop where you can see where trimming is required. You can see the trimming at the 8:20 mark of the video.

expert reply by: Bud M

0

Dan D.

3/17/2024

Hi Bud, the video you have shown below is no longer linked. Could you let us know if the suggestions have changed or if the link just needs to be updated? Thanks,

Bud M.

3/19/2024

@DanD The linked video is near the bottom of the page near the installation instructions for the etrailer Trailer Hitch Receiver # e95ZR.

Answer 1

The difference between the etrailer #e95ZR and Curt #C13427 trailer hitches for your 2023 Hyundai Palisade is literally just the finish. The etrailer hitch has a matte black finish while the Curt hitch has the classic glossy black finish that we see…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Hey Eddie, the Curt hitch part #C22RJ and the Trailermate part #TMT29FR are both very similar in design and capacity. I really like the Curt hitches and recommend them whenever available but Trailer Mate isn't bad either. If you are wanting the…

view full answer...

Is any Trimming Required To Install The etrailer Trailer Hitch Receiver On a 2023 Hyundai Palisade?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching