Replacement Locking Hitch Pin for Yakima OnRamp Bike Rack

Question

Question:

I am looking for the right hitch pin lock with keys for a Yakima on ramp hitch bike rack. Sku 1870800002 . Thx

asked by: Jeff M

0

Expert Reply:

The correct replacement hitch pin for a Yakima OnRamp bike rack # Y36FR is the part # Y8890200 and then for the locking core for the end of it you'd need the part # Y07235 and you'd be set.

expert reply by: Jameson C

0

Answer 1

Hey David, this is a great question and I have a solution but not probably exactly what you are looking for as the wider OnRamp LX ramp can't be used as-is with the original OnRamp bike rack. So what you can do is convert your OnRamp to an OnRamp…

view full answer...

Answer 2

Hey John, thanks for confirming for us that the wider LX trays like the part #Y63GD and Y67KD will work on the older Yakima OnRamp to allow it to fit wider tires. Like you noted you will need new T-bolts as well with part #Y88KV .

view full answer...

Answer 3

For the Yakima OnRamp bike rack #Y36FR the correct replacement pull pin is the part #8880530.

view full answer...

Answer 4

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 5

Hi Aaron, Are you referring to just the speed knob #8880904 or the tilting mechanism? If you're needing the tilting mechanism then you'd have to replace the shank as well with part #8880824. If you're referring to something else and want…

view full answer...

Answer 6

If you take a close look at the Replacement Latching Spring Pin part #8880582 you will see that the cylindrical body has two notches on either side. If you take an opened ended wrench and place it over the body while aligning it with these notches…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Locking Hitch Pin for Yakima OnRamp Bike Rack

Products Featured in This Question

Continue Researching