Will etrailer Replacement Clevis End Kit Fit Demco Base Plate Kit

Question

Question:

will this clevis kit fit on a demco baseplate? Replacement Clevis End Kit for etrailer XHD Tow Bar Item # e54ZR

asked by: Dwight T

1

Helpful Expert Reply:

Yes, the Replacement Clevis End Kit # e54ZR is compatible with both the etrailer and the Demco Classic and Tabless base plates.

Attached is a review video for you to check out.

expert reply by: Jon G

1

Answer 1

Hello Jeremiah, thanks for reaching out. We do have the Demco base plate and flat tow wire harness for your 2025 Ford Maverick. For that I recommend the following: - Demco Tabless Base Plate Kit - Removable Arms #DM38CV - Roadmaster 4-Diode Universal…

view full answer...

Answer 2

Hey Charles, yes our Demco base plate kit part #DM38CV is the same as the Demco base plate kit part number 9519366. The product pictures are probably an older version of what we used to carry that fit Mavericks.

view full answer...

Answer 3

Hi Mark, I totally get how frustrating that must be especially after choosing the Maverick for flat towing. I did find some updated info I can share with you, but the best way to stay on top of things for your specific vehicle is to use Ford’s…

view full answer...

Answer 4

Hey Ron! For your 2025 Ford Maverick I recommend going with the Roadmaster InvisiBrake Flat Tow Brake System #RM-8700 with the Roadmaster Stop Light Switch Kit #RM87GR and the Roadmaster Brake-Lite Relay Kit for Towed Vehicles #RM-88400. For wiring,…

view full answer...

Answer 5

Hey Steve, thanks for reaching out! The Roadmaster Direct-Connect Base Plate Kit #RM87NQ fits your 2025 Ford Maverick as long as it's the Hybrid model that doesn't have the engine block heater. It doesn't come with the 6-Pin connector,…

view full answer...

Answer 6

We can help you out, and I'll go ahead and list all the parts you will need to flat tow your 2019 Jeep Wrangler Unlimited with a standard plastic bumper and the Demco Commander II Non-Binding Tow Bar #DM9511012. - Base Plate Kit: etrailer…

view full answer...

Answer 7

Hello Joseph, thanks for reaching out. Our etrailer Base Plates like the #e98952 are actually made by Demco. It should absolutely be compatible with the clevis ends on your Demco tow bar. Any chance you could email me a picture of the tabs on your…

view full answer...

Answer 8

I went out to the warehouse and was able to get my hands on the Demco Tow Bar Adapter for Roadmaster XL and EZ Series Base Plates #DM9523001 and got the following measurements: -The overall length of 34", -The distance between the outmost tabs,…

view full answer...

Answer 9

Hey Jim! Since Demco doesn't have a base plate kit that fits the XLT model I recommend using the Blue Ox Base Plate Kit #BX2187. You can adapt this to your Commander using the Demco Tow Bar Adapter Brackets for Blue Ox Base Plates #DM9523041.…

view full answer...

Answer 10

The Demco Commander II Non-Binding Tow Bar - Victory Series - RV Mount - 2" Hitch - 6,000 lbs #DM9511012 typically comes with the connecting clevises to connect to the Demco Classic Base Plate Kit - Fixed Arms #DM9518072. However, if you need a…

view full answer...

Answer 11

Hi Eddie! What you are looking for is the Roadmaster Replacement Arms for Base Plate Kits #RM-ARMS. The 1541-1 is a Roadmaster baseplate part number and having that will help. You will need to scroll down the page a little bit and click where is says…

view full answer...

Answer 12

To attach your Reese tow bar to the Demco Classic Base Plate Kit #DM9518010 you were looking at you would need the an adapter #DM9523015. You'll remove the connectors from your tow bar (pictured below) and install the adapters in their place. The…

view full answer...

Will etrailer Replacement Clevis End Kit Fit Demco Base Plate Kit

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching