Replacement Entry Door Hinge Kit Needed for 2011 Tiffin Allegro Open Road 35QBA

Question

Question:

I am looking for replacement hinges for the entry door. Will LC95VR fit my entry door. 2011 Tiffin Allegro Open Road 35QBA

asked by: Deborah W

0

Expert Reply:

If the Replacement Controlled Motion Hinge for RV Entry Door - 6 Leaf - Black # LC95VR looks like what your 2011 Tiffin Allegro Open Road 35QBA has for the entry door then it will work. It has an overall length of 9-1/2" which you can compare to what you currently have on your motorhome along with the attached installation instructions.

This is a universal kit so there aren't specific RV fits listed for this product.

expert reply by: Jon G

0

Steps 1-5
(click to enlarge)

Steps 5-9
(click to enlarge)

Answer 1

We do carry a variety of replacement hinges that should work great with your 2011 Tiffin Allegro motorhome like the: -Replacement Entry Door Hinge for RV - 6 Leaf - White #LC198295 which has a total height of 9-1/4", and leaf widths of…

view full answer...

Answer 2

You can replace your Dometic 630035.331 condenser units with the Advent Air Replacement RV Air Conditioner for Dometic Setup w/ Start Capacitor - 15,000 Btu #ACDOM150 you were looking at and still retain use of your current air distribution box and…

view full answer...

Answer 3

In regards to selecting a tongue jack for a trailer, it only needs to be rated for the tongue weight of the trailer which is usually 10-15% of the gross trailer weight (GVWR). For example, if the trailer has a gross trailer weight of 5,500 lbs then…

view full answer...

Answer 4

Hey Dusty, I emailed the manufacturer to get the dimensions you are looking for on the #ABS56FR and the overall length is 5-5/32” with the hole spacing of 3-29/32” center to center.

view full answer...

Answer 5

Yes, the Replacement Entry Door Hinge part #LC198295 would work on your Tiffin Open Road 35QBA motorhome. This is a standard RV door hinge like what your Tiffin would have currently.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...