Replacement Light Switch and Housing Solution for Lippert Powered A-Frame Jack # LC285318

Question

Question:

I dropped the tailgate on my tongue jack and damaged both switches. The LC 49MD is the correct replacement for the jack switch, but I also need to on/off switch with the rubber boot that matches. Do you have that part number?

asked by: David R

0

Expert Reply:

Since you damaged the light switch and housing of your Lippert RV jack part # LC285318 what you'd want is the Replacement Top Cover with Switches # LC285160 and you'd have everything replaced that was damaged.

expert reply by: Jameson C

0

Answer 1

I have a couple options for you Matthew. First for the exact replacement from Lippert we have it in the Top Cover #LC285160. While we do have the Extend/Retract #LC49MD switch you found for your Jack #LC285318 we do not have the light switch…

view full answer...

Answer 2

According to the Lippert Service Manual for the Lippert Electric Trailer Jack #LC285318. "Maintenance 1. Before each use, inspect the Power Tongue Jack and replace if bent or damaged. 2. If wiring is connected to battery terminal, inspect at…

view full answer...

Answer 3

Yes, I confirmed with Lippert that the Replacement Top Cover for Lippert Components Electric Trailer Jack part #LC285160 will fit your Lippert 3,500 Lb Electric tongue Jack 1817941.

view full answer...

Answer 4

If the touch pad is showing "Retract Time out Return Levelers for service" all you need to do is hit, enter and retract at the same time. That will clear that code. I confirmed this with our contacts at Lippert.

view full answer...

Answer 5

Hey Amie, for the Lippert electric trailer jack part #LC285318 if you need replacement switches you'll need the replacement top cover #LC285160 as just the light switch is not available.

view full answer...

Answer 6

I would be happy to help! The replacement extend/retract switch for your Lippert Power Jack #LC285318 is not available by itself, so you will need the Replacement Top Cover for Lippert Electric Trailer Jack - Black #LC285160 which includes the new…

view full answer...

Answer 7

We do indeed offer a replacement upper and lower housing for the Lippert #LC285318 Electric Trailer Jack. The upper housing is part #LC285160, the lower housing is part #LC23UD which also includes the lamp lens.

view full answer...

Answer 8

To replace the extend/retract switch on your Lippert 181794 Electric Trailer Jack you'll simply need the Replacement Extend/Retract Switch for Lippert Electric Trailer Jack #LC49MD. If you're needing to replace the on/off or just both…

view full answer...

Answer 9

The Bottom Jack Cover #LC23UD of the Lippert jack #LC285318 has four screws in it that hold the top to it. You'll need to remove those screws first and take the top #LC285160 off. Once the top is off you can then dismantle the bottom cover from…

view full answer...

Answer 10

The Bottom Jack Cover #LC23UD has four screws in it that hold the top to it. You'll need to remove those screws first and take the top #LC285160 off. Once the top is off you can then dismantle the bottom cover from the jack and slide it off. Once…

view full answer...

Answer 11

The Replacement Extend/Retract Switch for Lippert Electric Trailer Jack #LC49MD is the correct switch for the Lippert Electric Trailer Jack with Footplate #LC285318 which does use 30 amps. Yes, the boot around the switch does seal the switch when…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Light Switch and Housing Solution for Lippert Powered A-Frame Jack # LC285318

Product Page this Question was Asked From

Continue Researching