Is the Replacement Extend/Retract Switch for Lippert Electric Trailer Jack Sealed and 30 amp Rated

Question

Question:

The boot around it means the switch is sealed I hope? And is it 30 amp it doesnt say this is from my Fox mountain 5th wheel it needs to be 30 amps

asked by: Daniel H

0

Expert Reply:

The Replacement Extend/Retract Switch for Lippert Electric Trailer Jack # LC49MD is the correct switch for the Lippert Electric Trailer Jack with Footplate # LC285318 which does use 30 amps. Yes, the boot around the switch does seal the switch when installed.

expert reply by: Scott S

0

Answer 1

It will indeed work; I just checked with Lippert for you and was able to verify the correct toggle switch for your Lippert Power Stance Electric Trailer Jack #LC69VR (which is the 813748), is the following: - Replacement Extend/Retract Switch for…

view full answer...

Answer 2

Since you damaged the light switch and housing of your Lippert RV jack part #LC285318 what you'd want is the Replacement Top Cover with Switches #LC285160 and you'd have everything replaced that was damaged.

view full answer...

Answer 3

I am not sure what your exact question is but the Lippert Power Gear Jack 181794 has been discontinued and there are no replacement parts available for this. Therefore, if you have an issue with yours then you will need to replace the entire jack and…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Hey Roger, The toggle switch for your FIC-ETJ3500 isn't a standard size so it looks like for a direct replacement you'll need to reach out to FIC Jack Services directly at 1-877-957-1501. If you aren't already I highly recommend using a…

view full answer...

Answer 6

Hi Collin, welcome back! The most economical replacement is going to be from Advent Air. You will need a complete system since everything moved to R32 refrigerant. If your upgraded thermostat is R32 compatible, or a smart thermostat that got a…

view full answer...

Answer 7

Thanks for reaching out, Doran! The toggle switch for your FIC-ETJ3500 is pretty unique and it looks like for a direct replacement you'll need to reach out to FIC Jack Services directly at 1-877-957-1501. You might consider looking at and…

view full answer...

Answer 8

To replace the Extend/Retract Switch for Lippert Electric Trailer Jack #LC49MD you'll just need to keep track of how the original was hooked up and replicate that. Unfortunately Lippert doesn't have a wiring diagram but we do have a photo we…

view full answer...

Answer 9

Thank you so much for the info and the pictures! According to my research it looks like your Cummins Onan RV Generator uses a 3/8" NPT Female fitting so you'll need a hose like part #100040-144-MBS. I have attached a link to all of our hose…

view full answer...

Answer 10

The 4110 primer is only available in a 1 Gallon #AL77CV like you found. We do have another TPO primer which comes in a 16oz Can #AL99CV.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Is the Replacement Extend/Retract Switch for Lippert Electric Trailer Jack Sealed and 30 amp Rated

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching