Correct Replacement Trailer Hub with .750 Inch Outer Bearing

Question

Question:

Need a trailer hub that fits a tapered spindle that measures 1.20 on the inside and .75 on the outside. Do you have one? Thanks!

asked by: Eric H

0

Expert Reply:

I believe we have what you're looking for in the Trailer Hub Assembly part # AH15450ECOMP which uses a LM67048 inner bearing (1.250") and a LM11949 outer bearings (0.750"). This is the only trailer hub assembly we offer which uses the LM11949 bearing. This hub has a 4 on 5" bolt pattern.

expert reply by: Conner L

0

Answer 1

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Hey Dave, for a saltwater boat trailer, powder-coated wheels wouldn't be my first choice, but they can still last quite a while if you're good about rinsing them thoroughly after each launch and sealing any chips or cracks in the finish as…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Hello Jason, thanks for reaching out. Yes, the Kenda Karrier KR53 ST205/75R15 tire with 15" black aluminum wheel #KE58JV does come balanced from the factory. Trailer tire and wheel assemblies are balanced by matching the tire’s high and low…

view full answer...

Answer 12

Great question, William! The Karrier ST225/75R15 #KE63KV is a KR35 while the Karrier ST225/75R15 #AM10303 is a KR03 according to Kenda. There is a slight variation in the tread pattern and from what Kenda says about them it looks like the KR03 is…

view full answer...

Correct Replacement Trailer Hub with .750 Inch Outer Bearing

Product Page this Question was Asked From

Continue Researching