Does The Exhaust Have to Be Lowered When Installing Curt Trailer Hitch Receiver On 2022 Toyota RAV4?

Question

Question:

Hello, I have the Rav4 2022 Hybrid XLE. I have heard talk of folks having to remove the exhausts to install the Hitch. I only have basic tools available and plan on jacking the car up on both sides in the rear for the installation. Do you foresee any issues like us having to remove the rear exhausts for the installation? Any other tips that you can provide would be helpful. -Thanks

asked by: Caitlin

0

Expert Reply:

The Curt Trailer Hitch Receiver # C13416 can be installed on your 2022 Toyota RAV4 Hybrid XLE without having to lower the exhaust. It will be easier to lift it into place with a 2nd set of hands to get around one of the exhaust tips and then the second. I recommend using a Nylon Brush # 814092 to clean out the threads on the frame nuts to prevent the chances of damaging the hardware during installation.

I recommend installing the Curt Vehicle Wiring Harness # C56434 when you install the receiver. It will be easier to route through the floor and secure to the receiver with the Mounting Bracket # C58001 if you prefer to not have it run through the rear lift gate when needed.

expert reply by: Bud M

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Does The Exhaust Have to Be Lowered When Installing Curt Trailer Hitch Receiver On 2022 Toyota RAV4?

Products Featured in This Question

Continue Researching