Overall Height of Timbren Suspension Enhancement Springs # TTORTUN4 for a 2010 Toyota Tacoma

Question

Question:

Can you tell me how tall the rubber spring and mounting bracket are? I want to make sure the clearance will be correct before I order the parts.

asked by: Colton C

0

Expert Reply:

I went out to the warehouse and actually pulled 2 possible fits for your 2010 Toyota Tacoma. First, for Timbren springs # TTORTUN4, the overall height from the bottom of the bracket to the top of the spring is approximately 5 inches.

The other kit I pulled was # TTORTUN4L. This kit is a bit shorter at 4-1/2 to 4-5/8 inches tall overall. I have included links to hte isntructions for both kits as well as a link to our FAQ article on Timbren systems for you.

expert reply by: Michael H

0

Answer 1

I reached out to Timbren, who told me the the actual jounce springs are both the same height at 3-3/4 inches, but the bracket height is different. So there aren't shorter springs, and the correct fit for your 2019 Toyota Tacoma 4WD is going to…

view full answer...

Answer 2

There are a few different options that we have for you to install a Timbren Rear Suspension Enhancement System on your 2010 Toyota Tacoma that is 4WD. Please keep in mind that any suspension enhancement system will not increase your weight capacity.…

view full answer...

Answer 3

The Timbren rear jounce spring kit #TTORTUN4L is the correct one for the 2012 Toyota Tacoma 4X4 non-Pre-Runner that has the OEM 3-leaf rear spring suspension. The bottom leaf of these springs can be seen in the linked photo that shows a…

view full answer...

Answer 4

The correct Timbren Rear Suspension Enhancement System for a 2019 Toyota Tacoma is part #TTORTUN4L if you have three leaves in the rear leaf spring pack or part #TTORTUN4 if you have four leaves in the rear leaf spring pack. Therefore, the main…

view full answer...

Answer 5

Hey Josh. The Timbren Rear Suspension Enhancement System item #TTORTUN4L has an overall height of 4.6" including the bracket. Timbren recommends a 1" gap between the spring and where the old bump stop hits. The Timbren item #TTORTUN4L is…

view full answer...

Answer 6

I went out and pulled both the Timbren kit part #TTORTUN4 and #TTORTUN4L from our warehouse to measure them for you and found that they both sit exactly 3-3/4 inches tall.

view full answer...

Answer 7

I definitely recommend going with the bump stop jounce-style springs that you are referring to as these require no maintenance and are very easy to install. They drastically reduce rear sag and also help with the overall handling of your truck. Your…

view full answer...

Answer 8

Timbren recommends a 1" gap when the Timbren Rear Suspension Enhancement System #TTORTUN4L is installed. The overall height of this kit is 4.6" so the distance between your leaf spring and the point of contact where the old bump stop hits…

view full answer...

Answer 9

I attached a picture that shows how the Timbren #TGMRTT35D that you referenced gets assembled. The spacer #TA25722-90P00 you referenced would go between the numbers 2 and 3 and you'd be set. See attached picture. You will need to provide a longer…

view full answer...

Answer 10

Assuming the lift kit you installed on your 2014 Toyota Tacoma is a suspension lift and not a body lift, the distance between the bottom of the factory bump stop and top of the contact point would have been altered. Unless the kit you installed…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Overall Height of Timbren Suspension Enhancement Springs # TTORTUN4 for a 2010 Toyota Tacoma

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching