Dimensions Of SuperSprings SumoSprings Helper Springs # SSR-612-40 For a 2020 Toyota Tacoma

Question

Question:

Can you provide the dimensions of this spring when uncompressed? I have a spring under axle conversion so I would like to figure out which spring will fit in my case

asked by: James

0

Expert Reply:

The SumoSprings Solo Custom Helper Springs # SSR-612-40 is 4" tall and 3" wide when uncompressed.

These are designed to be held in place under the U-bolts of a spring over axle and will likely not attach to your 2020 Toyota Tacoma with a spring under axle. I do not see that they have kit for your Tacoma with a spring under axle. If you can send me photos with measurements of your axle to frame I can check with SuperSprings to see if they have a different kit that may work with your Tacoma.

expert reply by: Bud M

0

Dimensions Of SuperSprings SumoSprings Helper Springs # SSR-612-40
(click to enlarge)

Chris H.

1/1/2026

I have 55 chevy , lower by 2inch , do you have a spring helper for this vehicle Chris

Robin H.

1/2/2026

@ChrisH all of the options are for stock height or you can add spacers if it is lifted. We don't carry anything designed to fit if it is lowered.

Answer 1

The bump stop is 5" long on the SumoSprings Solo Custom Helper Springs - Front Axle item #SSF-281-47. The bracket is 7/8". This is a confirmed fit for a 2009 GMC Topkick. I have attached a diagram I made below.

view full answer...

Answer 2

I reached out to Timbren, who told me the the actual jounce springs are both the same height at 3-3/4 inches, but the bracket height is different. So there aren't shorter springs, and the correct fit for your 2019 Toyota Tacoma 4WD is going to…

view full answer...

Answer 3

The Timbren rear jounce spring kit #TTORTUN4L is the correct one for the 2012 Toyota Tacoma 4X4 non-Pre-Runner that has the OEM 3-leaf rear spring suspension. The bottom leaf of these springs can be seen in the linked photo that shows a…

view full answer...

Answer 4

There are a few different options that we have for you to install a Timbren Rear Suspension Enhancement System on your 2010 Toyota Tacoma that is 4WD. Please keep in mind that any suspension enhancement system will not increase your weight capacity.…

view full answer...

Answer 5

I went out to the warehouse and actually pulled 2 possible fits for your 2010 Toyota Tacoma. First, for Timbren springs #TTORTUN4, the overall height from the bottom of the bracket to the top of the spring is approximately 5 inches. The other kit I…

view full answer...

Answer 6

Hey Josh. The Timbren Rear Suspension Enhancement System item #TTORTUN4L has an overall height of 4.6" including the bracket. Timbren recommends a 1" gap between the spring and where the old bump stop hits. The Timbren item #TTORTUN4L is…

view full answer...

Answer 7

The correct Timbren Rear Suspension Enhancement System for a 2019 Toyota Tacoma is part #TTORTUN4L if you have three leaves in the rear leaf spring pack or part #TTORTUN4 if you have four leaves in the rear leaf spring pack. Therefore, the main…

view full answer...

Answer 8

I went out and pulled both the Timbren kit part #TTORTUN4 and #TTORTUN4L from our warehouse to measure them for you and found that they both sit exactly 3-3/4 inches tall.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Dimensions Of SuperSprings SumoSprings Helper Springs # SSR-612-40 For a 2020 Toyota Tacoma

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching