Fit & Height of Timbren Suspension Enhancement on 2019 Toyota Tacoma 4WD

Question

Question:

What is the height of the springs in TT0RTUN4L kit VS TT0RTUN4 kit for my 2019 Tacoma 4WD? And can I get the shorter pair of springs separate from the kit ? I already have a kit where the springs are always in full contact with the frame.

asked by: Dennis R

0

Expert Reply:

I reached out to Timbren, who told me the the actual jounce springs are both the same height at 3-3/4 inches, but the bracket height is different. So there aren't shorter springs, and the correct fit for your 2019 Toyota Tacoma 4WD is going to depend on the number of OEM leaf springs your Tacoma has.

- 3 Leaf Springs: Timbren Rear Suspension Enhancement System # TTORTUN4L

- 4 Leaf Springs: Timbren Rear Suspension Enhancement System # TTORTUN4

So it is possible that you may have the kit with the taller bracket and would need the shorter, so I do recommend checking to see the number of leaf springs you have. I have added a link below to a video review for you to check out as well.

expert reply by: Kyle S

0

Answer 1

Hey Josh. The Timbren Rear Suspension Enhancement System item #TTORTUN4L has an overall height of 4.6" including the bracket. Timbren recommends a 1" gap between the spring and where the old bump stop hits. The Timbren item #TTORTUN4L is…

view full answer...

Answer 2

The Timbren rear jounce spring kit #TTORTUN4L is the correct one for the 2012 Toyota Tacoma 4X4 non-Pre-Runner that has the OEM 3-leaf rear spring suspension. The bottom leaf of these springs can be seen in the linked photo that shows a…

view full answer...

Answer 3

There are a few different options that we have for you to install a Timbren Rear Suspension Enhancement System on your 2010 Toyota Tacoma that is 4WD. Please keep in mind that any suspension enhancement system will not increase your weight capacity.…

view full answer...

Answer 4

I went out to the warehouse and actually pulled 2 possible fits for your 2010 Toyota Tacoma. First, for Timbren springs #TTORTUN4, the overall height from the bottom of the bracket to the top of the spring is approximately 5 inches. The other kit I…

view full answer...

Answer 5

The correct Timbren Rear Suspension Enhancement System for a 2019 Toyota Tacoma is part #TTORTUN4L if you have three leaves in the rear leaf spring pack or part #TTORTUN4 if you have four leaves in the rear leaf spring pack. Therefore, the main…

view full answer...

Answer 6

The SumoSprings Solo Custom Helper Springs #SSR-612-40 is 4" tall and 3" wide when uncompressed. These are designed to be held in place under the U-bolts of a spring over axle and will likely not attach to your 2020 Toyota Tacoma with a…

view full answer...

Answer 7

I found the article you mentioned from Timbren and a 1 inch gap is recommended for the rear kits but for the front kits they recommend no gap at all. Since the part #TGMFK25D is a front kit you'd want to not have any gap at all.

view full answer...

Answer 8

I went out and pulled both the Timbren kit part #TTORTUN4 and #TTORTUN4L from our warehouse to measure them for you and found that they both sit exactly 3-3/4 inches tall.

view full answer...

Answer 9

For your 2013 Toyota Tundra that is towing a 6,500 lb travel trailer I'd go with the Timbren kit part #TABSOSR to help support the rear of it and reduce sag as this will give you up to an additional 3,600 lbs of support if needed. Other kits…

view full answer...

Answer 10

The Timbren Active Off-Road Bumpstops part #TABSOSR which are a fit for a 2007 Toyota Tacoma are designed so that there is more space between the spring and frame to allow the suspension to articulate freely when off-road. If you're looking for a…

view full answer...

Answer 11

The Timbren Active Off-Road Bumpstops #TABSOSR referenced in your question feature an assembled height of 4-5/8 inches. I have attached a short video review on this kit along with the written installation instructions that you can check out as well.

view full answer...

Answer 12

To add a 1" spacer #A25723-90AH00 to the Timbren Active Off-Road Bumpstops #TABSOSR you were looking at for your 2014 Toyota Tundra you will need to purchase two grade 5 or 8 3/8" x 2-1/2" F/T UNC bolts from your local hardware store.…

view full answer...

Fit & Height of Timbren Suspension Enhancement on 2019 Toyota Tacoma 4WD

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching