How to Add Equalizer Upgrade to Older Trailer with Straight Equalizer
Updated 08/01/2022 | Published 07/30/2022
Products Featured in This Question
Question:
I have a 1968 Ken-craft tandem-axle camper and was considering upgrading the equalizers in the leaf spring suspension. However, my old equalizers have the mounting hole in line with the shackle mounts, not in a triangle configuration like current trailers, so the Road Armor or Morryde units wont work without cutting the tab off the frame and welding on a shorter one, which Id rather not do. My equalizer mount hole is about 4 1/2 inches below the frame, and the holes for the shackles are about 5 1/2 inches apart both measurements center-to-center. I have a picture, but I dont see an attachment function on this form. Any suggestions?
asked by: David W
Expert Reply:
The straight equalizers, like the 5-1/2" Long # TREQR2 it sounds you have, don't really have any upgrade options available as those aren't as common as the triangular versions you were talking about.
In order to upgrade the suspension on your trailer you could either install a new hanger kit or you could use the outer mounting brackets for the Correct Track Trailer Alignment and Lift Kit # RR23QX to lower those by 2-1/4" so you can then use the Equa-Flex Cushioned Equalizers # LC279687. At this point though I would rather just pursue the hangers as it would be much more cost-effective to go that route.
Attached is a video for you to check out.
Product Page this Question was Asked From
Straight Equalizer for 1-3/4" Double-Eye Springs - 5-1/2" Long - 9/16" Center Hole
- Trailer Suspension Parts
- Standard Equalizer
- Camper
- Car Hauler
- Utility Trailer
- Double Eye Springs
- 5-1/2 Inch Long
- Tandem Axle
- Triple Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: morryde trailer suspension parts
- Search Results: lift kits for trailer
- Search Results: 5way trailer harness
- Search Results: dot reflective tape
- Search Results: timken bearing for dexter 3500 lb axles
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps
- Shop: Lippert Road Armor Shock-Absorbing Equalizer Kit - Tandem Axle - 3,500-8,000 lbs
- Search Results: seal 10~19
- Search Results: 3500 lb axle bearings
- Video: Ultimate Overview of the MORryde Suspension Upgrade Kit for Tandem Axle Trailers
- Q&A: Recommended MORryde Suspension Upgrade Kit for Tandem Axle Trailers w/ 3-1/8" Long Shackle Straps
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Shop: Correct Track Trailer Alignment and Lift Kit - Tandem Axle
- Q&A: How To Increase Bed Rail Clearance When Pulling 5th Wheel Camper With 2024 Ford F-450
- Shop: Trailer Wiring
- Video: A Closer Look at the Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles
- Shop: Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Tandem Axle - 6,000 lbs
- Shop: Curt Air Ride 5th Wheel Pin Box - Lippert 1621 & 1621HD - 21,000 lbs
- Shop: Timken Bearing Kit for 3,500 lb Axles with #84 Spindle - Bearings L44649/L68149
- Shop: CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
- Q&A: Upgrading Equa-Flex Equalizers On a Tandem Axle Trailer with 5,200 Lb Axles
- Q&A: Lift Kit Solution to Allow Fifth Wheel Trailer to Sit More Level When Towed
- Video: Review of RV Ride Control Trailer Suspension Parts - Alignment and Lift Kits - RR23QX
- Q&A: Replacing Straight with Triangular Equalizers On a Trailer
- Q&A: Will A Different Shape Or Style Of Equalizer Be A Problem On My 2006 Zinger Trailer?
- Shop: Suspension Enhancement
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Trailer Suspension Parts
