Replacing Straight with Triangular Equalizers On a Trailer
Updated 04/26/2021 | Published 04/22/2021
Question:
I am looking to use the TREQ310 to: 1. Replace the flat equalizer and give my trailer roughly a 3inch lift. 2. Hopefully eliminate the unequal level of the spring arms
asked by: Matt N
Helpful Expert Reply:
In order to confirm fit of the Triangular Equalizer for 1-3/4" Double-Eye Springs part # TREQ310 you need to verify the spacing between the lowermost holes on the equalizer either matches what is currently installed on the trailer or will match when new shackles straps are also installed to make up the difference. The above equalizer measures 6-1/16". The height of the equalizer is not as important. It will provide lift if going to a taller option but it's not a direct 1:1 ratio.
If you need different length shackle straps I have attached our selection below.
Product Page this Question was Asked From
Triangular Equalizer for 1-3/4" Double-Eye Springs - 6" Long - 9/16" Center Hole
- Trailer Suspension Parts
- Standard Equalizer
- Camper
- Car Hauler
- Utility Trailer
- Double Eye Springs
- 6-1/16 Inch Long
- Tandem Axle
- Triple Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Lippert Road Armor Shock-Absorbing Equalizer Kit - Tandem Axle - 3,500-8,000 lbs
- Search Results: timken bearing for dexter 3500 lb axles
- Search Results: dot reflective tape
- Search Results: 5way trailer harness
- Search Results: 5 pin wiring harness
- Search Results: 3500 lb axle bearings
- Search Results: seal 10~19
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Search Results: cushioned equalizer
- Shop: CE Smith Swivel Bracket for Boat Trailers - Galvanized Steel - 2" Hole Centers - Qty 1
- Video: A Closer Look at the Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles
- Shop: Trailer Wiring
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
- Q&A: Recommended Timbren Silent Ride Suspension for 2-3/8" Axles
- Shop: etrailer Rust-Resistant 4-Leaf Double Eye Spring for 3.5K Trailer Axles - 25-1/4" - Dacromet
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps
- Shop: Zinc Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Q&A: How to Add Equalizer Upgrade to Older Trailer with Straight Equalizer
- Q&A: Will A Different Shape Or Style Of Equalizer Be A Problem On My 2006 Zinger Trailer?
- Q&A: Timken Bearing Kit Fitment for a 3,500 lb Axle
- Q&A: Replacement Inner Member for UFP A-60 Surge Coupler for Tandem Disc Brake Setup
- Q&A: Replacement Inner Member Assembly for UFP A 60 Surge Brake Coupler
- Shop: Suspension Enhancement
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: How to Measure for Trailer Hitch Drop
- Shop: Brake Controller
on Trailer Suspension Parts
