How To Install The Furrion Vision S RV Camera System On A Trailer
Published 07/21/2022
Products Featured in This Question
Question:
What is required for installation on the trailer?
asked by: Mike B
Expert Reply:
If your trailer isn't prewired for Furrion then to install the Furrion Vision S Wireless RV Backup Camera System # FOS05TASF you'll first need to determine the mounting location. Typically, we wire these to the running light circuit so that you can power the camera on whenever you want instead of on when the tow vehicle is in reverse.
Trailer's typically have a running light towards the top middle of the trailer, and you'll need to splice into the wiring of this light to power the camera. You'll want the camera towards the top middle of the back wall either above or below this running light. You'll drill a hole in the wall for the wiring to pass through and run your wire up or down to the light and pop the light off the trailer to get to the wiring.
From there you can splice the positive and negative wires of the camera to the positive and negative wires of the light using some heat shrink butt connectors # DW05744-5. Once the wiring is complete you can reinstall the light and then push your camera wiring into the wall of the trailer.
Next you can mount the camera to the wall of the trailer, it will not include screws so you will need some self-tapping screws, which you can get at your local hardware store. Once it's mounted, I always take some clear silicone over the top of the mount to ensure no water can get behind it.
For tools all you should need is a ladder, wire strippers # PT43ZR, and wire crimps # PTW30764.
Once all of this is complete all you need to do is pair the camera.
If you are prewired for Furrion then all you need to do is remove the cover on the mount and plug in your camera. I've attached a video of this process below to help walk you through it as well.
Product Page this Question was Asked From
Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 5" Screen
- RV Camera System
- Backup Camera
- Observation Camera
- Anti-Glare
- Mirrored Image
- Motion Detecting
- Night Vision
- Touch Screen
- Waterproof
- Pre-Wired RVs
- Wireless
- Wide View
- Dashboard Mounting Bracket
- Suction Cup Mount
- Side Marker
- 5 Inch Display
- 3 Cameras
- Furrion
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Furrion Vision S+ Wireless RV Backup System w/ 1 Camera - 7" Screen
- Search Results: 16 x 16 roof vents
- Shop: 7-Way Vehicle Power Adapter for Furrion RV Observation Camera
- Q&A: RV Seat Cover that Fits 2014 Forest River Georgetown XL
- Shop: Vehicle Seat Covers
- Shop: Trailer Wiring
- Shop: Classic Accessories RV Captain Seat Cover
- Shop: Phoenix USA Rear Wheel Center Cap - 8-1/4" Hub Diameter - Center Hole Mount - Left Thread
- Shop: Replacement Main Board Assembly for WFCO Auto-Detect RV Power Centers - 45 Amp
- Q&A: Looking For Gas Strut For Stabilus Lift-O-Mat Awning 3108392.303
- Shop: Replacement Bracket Kit for pre-2019 Solera RV Slide-Out Awnings - Black
- Shop: Replacement Pin for Solera RV Awnings
- Q&A: Recommended Replacement Water Heater for Atwood GC6AA-10E
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Video: How to Choose a Trailer Brake Controller
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer jack
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Shop: Brake Controller
- Article: How to Measure Your Trailer Wheel Bolt Pattern
on RV Camera System
