Exhaust Hanger on 2011 Nissan Rogue Interferes with Trailer Hitch Installation
Updated 10/01/2013 | Published 09/29/2013
Question:
I am trying to install my Curt hitch on a 2011 Nissan Rogue SV. On the driver side, I can not get it in the correct holes because the silver bolt from the exhaust is right in the spot where the hitch is supposed to go so I can not move it in correctly. Is there a way to push back the exhaust bolt or move the male end coming out to the other side? I did double checked all the bolts holes and I did make sure I am using the correct holes and everything else lines up.
asked by: Aaron
Expert Reply:
You should be able to bend the exhaust hanger a little bit to allow the hitch to fit easily on the vehicle. The installation instructions state that lower the exhaust will make installation easier. If you remove the exhaust from the rubber hanger, using a strap of some kind to support the exhaust some, put the hitch in place and then put the exhaust back up on the hanger it might not interfere at all.
If it still does then bending the hanger some is perfectly fine and will not hurt anything. I have included a link to a video that shows the typical method of lowering exhaust. I have also linked an FAQ article that, in part, shows you how to bend a hanger.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: etrailer D-Shape Anti-Rattle Locking Hitch Pin for Benton Hitch Accessories- 2" Hitches
- Shop: Benton ShiftShow Bike Rack for 4 Bikes - 2" Hitches - Tilts w/ Bikes Loaded
- Video: First Impressions of the Benton ShiftShow 4 Bike Rack
- Video: Review of etrailer Hitch Anti-Rattle - Hitch Lock - e43JR
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: How to Choose a Trailer Brake Controller
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Shop: Brake Controller
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Comparing the Curt Hitch C13416 and EcoHitch Hitch 306-X7396 for a 2019 Toyota RAV4
- Search Results: trailer jack
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer hitch ball mount
on Trailer Hitch
