Spindle Nut to Use with Spindle TRU27FR

Question

Question:

What castle nut part number would be used on this spindle?

asked by: Jeff

0

Expert Reply:

The correct spindle nut to use with the spindle part # TRU27FR is the part # 165686.

expert reply by: Jameson C

0

Answer 1

The thread diameter of spindle jam nut #6-191 is 1 inch. If you do need a 3/4 inch then this nut will not work, though it is for EZ lube spindles that have the grease zerk at the end. We do not have a 3/4 inch jam nut. The closest match is a 7/8 inch…

view full answer...

Answer 2

For castle nut #165931, for a D washer use part #5-23 or round washer use part #SW1000. These are both for 1 inch spindles but are compatible with the 7/8 inch castle nut assemblies. You can also use the Replacement Spindle Washer - Tang Type for E-Z…

view full answer...

Answer 3

In order to find the correct replacement hub and spindle you will need to know the capacity of your axle along with the bearings you currently have. In order to find the size of the bearings you can look for part numbers on your existing bearings. If…

view full answer...

Answer 4

You will need 2 of the Easy Grease Trailer Idler Hubs #AKIHUB-545-2-LFEZ-2K for your trailer hubs. This hub fits on your Spindle #TRU27FR and will include new bearings, races, a grease seal, grease cap, and new lug nuts. As you have an EZ grease…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Spindle Nut to Use with Spindle TRU27FR

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching