Correct Replacement Threaded Hitch Pin for Yakima BuckHorn 4 Bike Rack

Question

Question:

I need a 1/2” threaded hitch bolt for a Yakima Buckhorn 4” receiver. Can you help me? Thanks,

asked by: Peter

0

Expert Reply:

The correct replacement threaded hitch pin for the Yakima BuckHorn 4 Bike Rack is the Replacement Hitch Bolt and Clip for Yakima HoldUp and BigHorn Bike Carriers part # Y8890200.

expert reply by: Conner L

0

Answer 1

For a replacement hitch pin for your Yakima BuckHorn bike rack you would want the part #Y8780018.

view full answer...

Answer 2

I spoke with my contact in the Tech Services department at Yakima, who tells me that the #Y8890174 adapter you mentioned is not compatible with the BigHorn 4 Bike rack you have. Instead of going with the adapter, you would need to replace the…

view full answer...

Answer 3

With the EcoHitch Stealth Trailer Hitch Receiver #306-X7365 installed on your 2024 Subaru Crosstrek Wilderness the only portion of the receiver you will see is the removable 2" receiver opening. I have included an image of the receiver installed…

view full answer...

Answer 4

The Yakima Holdup 2 bike rack 2009-2012 which fits inside a 2" receiver is model number 8002433. This will use the Replacement Tilt Pull Pin #Y39FR. The Anti-Rattle #8890260 is the correct anti-rattle as is the End Cap #8880228. I do not see…

view full answer...

Answer 5

I believe you are referring to the Yakima HoldUp #Y02443. If you need just the HitchLock alone, that is the #Y07235. However, if you need the hitch pin that is compatible with both the HitchLock and the HoldUp itself, that is the #Y8890200.

view full answer...

Answer 6

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt and is the same bolt that comes with the part #8890260. The size wrench you would use to install or remove this bolt is 15/16…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Correct Replacement Threaded Hitch Pin for Yakima BuckHorn 4 Bike Rack

Product Page this Question was Asked From

Continue Researching