How Many Spacers For SumoSprings on 2019 Ford F-250

Question

Question:

I have a 2022 F250 with standard leaf set up. What is the recommended spacers to use with the SSR-127-47 Sumo Springs. Each comes with a 1 inch and 2 x 1/2 inch. I tow a bumper pull camper occaisonally and bobcat and trailer. I probably drive unloaded much more than loaded so just curious what people are doing for spacer set up. I would like the quickest engagment possible but I also dont what to keel kick back if they are engaging when I am empty and going over bumps. Thank you.

asked by: Kris

0

Expert Reply:

SumoSprings recommends 1/2" to 1" of space once installed on your 2019 Ford F-250. This varies between vehicles so since you want the quickest engagement I would aim for the 1/2" space. You will have to use one of the 1/2" spacers regardless for the installation of the # SSR-127-47, so I would check and see what it looks like when you put it on and go from there. If the addition of an extra spacer would give you less than 1/2" I would not add another in.

expert reply by: Robin H

0

Answer 1

The SumoSprings Solo Custom Helper Springs item #SSR-405-47 that fit a 2012 - 2023 Jeep Wrangler should have a 1/2" to an 1" of space between them and your axle.

view full answer...

Answer 2

I measured the SumoSprings Trailer Helper Springs #TSS-107-40 and it will be either 6-3/4" with both spacers, 6-1/4" with one spacer, or 5-3/4" with no spacer when measured from the top of the U-Bolt plate to the top of the spring once…

view full answer...

Answer 3

It's going to vary some from vehicle to vehicle just because of how your truck rides. However, I reached out to SuperSprings and they told me that a half inch to an inch of clearance between the spring and the frame is fairly standard. The…

view full answer...

Answer 4

Hey Jeff, SumoSprings do not need to be touching the axle when unloaded. Having a bit of a gap while unloaded is totally normal. Giving your axle a bit of wiggle room before engaging the jounce spring will give you a bit more of a comfortable ride.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

This is a great choice Joe and thanks for reaching out! Weigh Safe True Tow Weight Distribution Hitch #WS49MR would be a good match for your setup. Since your Grand Design toy hauler will have a loaded tongue weight between 1,300 and 1,600 lbs, this…

view full answer...

Answer 11

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 12

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

How Many Spacers For SumoSprings on 2019 Ford F-250

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching