Matching Back Cover to Use with Solera Awning Head Cover # LC643922

Question

Question:

What would be the back part number for the part number LC643922. I need front and back Thanks

asked by: Bryan B

0

Expert Reply:

The back cover that matches the # LC643922 that you referenced is the part # LC643921.

expert reply by: Jameson C

0

Answer 1

In order to separate two awning head covers such as the Solera Awning Plain Drive Head Front Cover part #LC289560 and the Solera Awning Plain Drive Head Back Cover part #LC289561 you'll need to remove the screws which are accessed from the back…

view full answer...

Answer 2

Thanks for the information. I checked with Lippert and didn't get anything back on the first two numbers and the last one is a fire safety code. The good thing is there aren't many options for replacement motor covers for Solera awnings. I…

view full answer...

Answer 3

Hello Mo, thanks for reaching out. According to Solera, the screws for their head covers are 6-15 UNF x 1/2”. We do not carry the screws by themselves, but if you check your local hardware store you should be able to find some thing compatible.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Matching Back Cover to Use with Solera Awning Head Cover # LC643922

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching