Correct etrailer Trailer Hitch Receiver for a 2015 Toyota Tacoma

Question

Question:

e98850 Does it fir 2015 tacoma

asked by: Dale M

0

Expert Reply:

The correct etrailer Trailer Hitch Receiver for a 2015 Toyota Tacoma is indeed part # e98850 but please note, it cannot be used to replace a factory trailer hitch if equipped, it's only designed to be added to models without one.

expert reply by: Conner L

0

Answer 1

Hi Steve; the factory hitch on the 2013 Tacoma has the bumper brackets integrated into the hitch. You can replace it with the etrailer Trailer Hitch #e98850 but you will have to remove the old hitch and find new bumper brackets to complete the…

view full answer...

Answer 2

Based on the information I could find online the bumper brackets are integrated into the factory receiver. I have also read some of the factory receivers may have been welded to either the frame or bumper components. You will need to check your…

view full answer...

Answer 3

Hey Mark, for your 2014 Toyota Tacoma the hitch I would recommend is the etrailer part #e98850 which has great towing capacities and is mostly hidden. Then for trailer wiring the Tekonsha kit part #118496 is the easiest to install and most reliable…

view full answer...

Answer 4

The etrailer Hitch item #e98850 you were looking at, is custom fit so the holes will line up on your 2014 Toyota Tacoma if you do not have a factory hitch installed. This hitch does include all of the necessary mounting hardware to complete the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

Hey Kelly! The Curt 13146 fits 2016 - 2022 Honda Pilot. What you need for your 2026 Honda Pilot is the Curt #C22HR. This has a bolt-on installation and does not require any cutting or trimming of the bumper so you won't be modifying the vehicle.…

view full answer...

Correct etrailer Trailer Hitch Receiver for a 2015 Toyota Tacoma

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching