Correct Ball Mounts For The Furrion Vision S Wireless RV Backup Camera System

Question

Question:

What size ball 17mm or 20mm is used to mount the 7in screen. Thanks!

asked by: Mark D

0

Expert Reply:

I checked with Furrion and the 7 inch and 5 inch monitor version of the Furrion observation system # FOS05TASF use part # FR79SR. The smaller 4.3 inch size use the part # LC776462.

The ball of the # FR79SR is 0.85" or 21.59mm and the ball of the # LC776462 is 0.60" or 15.24mm.

expert reply by: Kevin C

0

Kenton B.

2/9/2025

Thank you for this information. It was very helpful!

Kevin C.

2/10/2025

@KentonB No problem, if you end up needing anything else just let us know.

Answer 1

Thank you so much for the info and the pictures! According to my research it looks like your Cummins Onan RV Generator uses a 3/8" NPT Female fitting so you'll need a hose like part #100040-144-MBS. I have attached a link to all of our hose…

view full answer...

Answer 2

The actual puck itself is a standardized size between each brand so the only measurement that matters is the spacing of the pucks, which differs between each vehicle manufacturer. I've attached a diagram below with the spacings used by…

view full answer...

Answer 3

Given that the mount of the Torklift #TLA7844 is 2-1/2 inches wider than the available spot on the landing, these particular steps wouldn't be the best choice. CR Brophy makes a narrower 4 step unit, part #AS04 that would be a better choice. This…

view full answer...

Answer 4

Yes the Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL88295 are compatible with the OEM 5th wheel puck system on your 2014 Ram 3500. I confirmed this with my contact at Air Lift. I also recommend installing a compressor kit like the Air…

view full answer...

Answer 5

I spoke with my contact at Furrion and the barrel connector size of the Furrion RV Observation Camera System part #FOS05TASF is 2.5 mm x 5.5 mm.

view full answer...

Answer 6

Hey Randy! I can't really say for sure if that canopy will be in the way of the Furrion Vision S+ Wireless RV Backup System #FR57AD. The camera can be tilted, and has a 140º viewing angle, but I expect it will be at least partially blocked…

view full answer...

Answer 7

Hey Kevin, thanks for reaching out again! The TorkLift SuperTruss Hitch Extension for SuperHitch Trailer Hitch Receivers #TLE1542 measure 42" from the center of on hitch pin hole to the center of the other hitch pin hole. I've attached an…

view full answer...

Answer 8

Hi Tim; I reached out to Go Power and their representative told me the flashing on the Go Power Sun Cycle Advanced Lithium RV Battery #GP99QR meant it is in sleep mode, so the "battery charge path is enabled but discharge path is disabled and…

view full answer...

Answer 9

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 10

Hi Steve, I checked with our team that handles this and can confirm the hardwired, 50 amp Power Watchdog Surge Protector with Bluetooth, WiFi, and Emergency Shut Down #HU82VR is the Gen II version.

view full answer...

Answer 11

Hey David, you will only need to install one of the 12V PWM Filters item #VGR64VR if you do it upstream before the circuit branches off to the separate cameras. You do not need one at each camera. It's a bummer about the Furrion adapter you tried…

view full answer...

Answer 12

Hey Mike, it is important that you use the included power cable with the Furrion Vision S+ Wireless RV Backup System w/ 1 Camera #FR57AD like the instructions indicate. If this is like a hardwire install I would look for a cigarette lighter to 2-wire…

view full answer...

Correct Ball Mounts For The Furrion Vision S Wireless RV Backup Camera System

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching