Does Furrion Vision S+ Have to Use Included Power Cable for Monitor
Updated 04/30/2026 | Published 07/15/2025 >
Question:
I recently purchased this Vision S+ system, but havent installed it yet. The instructions for the 7inch monitor state The allowed input voltage to the monitor is 5V only use Furrion authorized cigarette adapter to connect the monitor.Any other branded adapter may damage the monitor permanently and will void the warranty. I am replacing a Vision S 5inch system and my monitor currently is powered by a 12V feed. Is there some voltage step-down in the Furrion harness that the voltage to 5V, or is this a mis-print?
asked by: Mike D
Expert Reply:
Hey Mike, it is important that you use the included power cable with the Furrion Vision S+ Wireless RV Backup System w/ 1 Camera # FR57AD like the instructions indicate. If this is like a hardwire install I would look for a cigarette lighter to 2-wire adapter so that you can wire it in and use the correct connector that will allow you to have the correct voltage for it.

Bob
4/29/2026
Where could I find a power cord for my s+ camera system. My connection to the camera broke so I need a new cord.

Product Page this Question was Asked From
Furrion Vision S+ Wireless RV Backup System w/ 1 Camera - 7" Screen
- RV Camera System
- Backup Camera
- Built-In Microphone
- Night Vision
- Waterproof
- Pre-Wired RVs
- Wireless
- Standard View
- Suction Cup Mount
- Rear
- 7 Inch Display
- 1 Camera
- Furrion
more information >
Continue Researching
- Shop: Furrion Monitor Power Adapter Cable - Cigarette Plug to 5V USB-C
- Shop: Furrion Vision S+ Wireless RV Backup System w/ 1 Camera - 7" Screen
- Shop: Replacement 7" Monitor for Furrion Vision S+ Wireless RV Camera Systems
- Shop: Suspension Enhancement
- Shop: Tonneau Cover
- Search Results: chill cube
- Shop: Furrion Vision S+ Wireless RV Backup System w/ 1 Camera - 5" Screen
- Shop: Furrion Vision S+ Wireless RV Observation System w/ 3 Cameras - 7" Screen
- Shop: RV Camera
- Search Results: furrion rv camera system
- Search Results: ebrhx~adh~na
- Search Results: 3 cameras rv camera system
- Search Results: ebrh~accna
- Search Results: facr18hepa~ps~am
- Search Results: smartplug shore power cord
- Video: Review of Furrion Monitor Power Adapter Cable Vision S Plus - FR54AF
- Shop: Furrion USB-A to USB-C Power Cable - 5' Long
- Video: Review of Furrion USB A To USB C Power Cable Vision S Plus - FR34AF
- Video: Installing the etrailer Hard Folding Tonneau Cover on a 2025 GMC Sierra 2500
- Shop: Replacement Power Cable for Furrion Vision 1, Vision 2, and Vision S Doorway Camera Brackets
- Video: Review of Lippert Replacement 7 In Monitor Vision S Plus Wireless RV Camera System - LC67FP
- Video: Review of Furrion Replacement Monitor Cigarette Power Cable Vision 1 And 2 Camera System - FR88EF
- Video: Hands-On with the etrailer Electric Trailer Jack with 7-Way and SnapPad
- Shop: Brake Controller
- Shop: RV Jack Pads
- Shop: Fifth Wheel Hitch
- Video: Installing the Furrion Vision S+ Wireless RV Backup System on a 2025 Forest River Columbus 380RL Fif
- Shop: Trailer Wiring
- Q&A: Backup Camera for 2025 Forest River Rockwood Mini Lite 2205S
- Q&A: Replacement Lens for Petersen Clearance Side Marker Trailer Light With Reflex Dimensions


Mike D.
7/17/2025
Thank you. After more research, I found a 12V to 5V converter with USB outlets that I will wire into my system. I'm doing this because I already have a clean 12V run to my monitor location and it's easier than re-wiring the whole thing. Thanks for your input!