Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replaces the suction cup mount for your Furrion Vision S wireless RV backup camera system (FOS43TASF) with a 4.3" monitor.
Features:
Note: If you have a Vision S camera system with a 5" or 7" monitor, order part number FR79SR.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the replacement suction cup mount for the Furrion Vision S wireless RV backup camera system. Now this part will replace the suction cup mount on your Furrion Vision S wireless RV backup camera system that has the 4.3 in size monitor. That's part number FOS43TASF, and that system we do sell separately on our website. Basically this mount will allow you to mount your monitor or your camera system anywhere you want. The monitor will just snap onto the ball of this mount and allows the monitor to rotate to any positions that need it. This part will include one suction cup mount, and then just show you how it mounts.
I have like a metal surface here, so you could just put your mount on here, and then if you just push down with your lever right here on the back as you push that down, it'll form a suction and you can see there's no way that's going to be moved anywhere.And then to remove it, just pull back up on that, and then pull up on the little tab here to remove the suction. But again, it can be put on anywhere you'd like. Push down on that, and it'll hold it into any position. And to remove it, just pull up on it, and pull that tab to release it. Very simple.
But that should do it for the review on the replacement suction cup mount for the Furrion Vision S wireless RV backup camera system.
This is a difficult mount to find with the 16.5mm ball, so glad I found it here. I noticed this is sought after, perhaps because the one that come with the original back-up camera system breaks without abuse. Shipping time wasn’t bad, even with a holiday weekend as I noticed etrailer.com actually shipped the item same day, thank you.
This mount is correct and fit perfectly, just as expected.
We have been using this replacement part for a year niw in the brutal Florida heat and it’s holding up well.
If and when we need to replace again I’ll for sure come back and re-order one from here
Michelle
9/30/2025
Still holding up !!! Happy to say hook still working perfectly
Pay attention to the ball and socket mount in the 2nd photo before you order. The ball is way too small to work in that hole. It's the wrong mount for the Model FOS05TASF 4.3" monitor. I was sent 2 that were identical and had a 15.7mm ball instead of a 22.5mm ball. If you have that model monitor do not order the LC776462. The price is good but it won't fit. They just gave up trying to help after sending me the same incorrect part twice. Did'nt call Lippert/Furrion to figure out they were showing the wrong part on the web page for that model and apparently don't have the right one.
Received item quickly. Customer service was helpful via email in choosing which replacement suction cup to order.
Wrong size
I was hesitant to order this after reading some of the reviews. At first I didn't think it was going fit my Bluetooth camera monitoring screen.. but with just the right amount of pressure the ball popped into the hole snd it wirks perfectly. With the pressure required to get into the hole, I can see why others didn't think it fit correctly. I dont know if I will ever get it out of the hole, but I slso don't see a reason to. Overall - Very Satisfied. And glad I could find a replacement. The camera came with a used trailer I bought and the previous owner didn't provide this mount.
Delivered quickly and followed up to make sure it was right
Perfect fit. Works as advertised. Pretty quick delivery.
Replaced my camera mount in lest then 5 days!!
After the suction for my campers backup camera had a melt down because of excessive heat on my windshield I went looking for a replacement. I went to every RV and Car place within 30 miles of home and could not find one with the size ball to fit my monitor. One place I visited looked up online and found what I needed in less than two minutes and suggested I order one online as it would be cheaper than him doing it for me. I did what he suggested and four days later I have the correct part in hand. Next time I’ll do that first as I probably spend more in fuel cost driving around than I did for the part.
Thank you…
Rick
7/23/2024
Performing as expected. The new suction cup has not seen a temperature above 110 deg. F where as the one I replaced had seen up to 118 deg F which could be a contributing factor in its failure.
Perfect fit.
Exactly what I needed to replace my old suction cup.
Ice mount just like factory mount
They charge me fifty something bucks for a part that is way too small. What's the point in providing the model number if you're not going to follow it. Now I need to figure out how I'm going to get my money back
Super easy install and setup
This part was an exact fit.
Rating is because I have the wrong suction mount. Needed the 7 inch.
Got the wrong size ball, but I love it so I ordered another one with the correct item number
Works perfectly. Fit and finish are same quality of original one that the sun cooked.
This is perfect for my needs
Perfect fit and quality.
It fits perfectly.
works great
This mount does Not fit this monitor. The ball is way too small
Katrina B.
5/2/2022
This item is designed to replace the suction cup mount for your Furrion Vision S wireless RV backup camera system [part # FOS43TASF] with a 4.3 inch monitor. Can you please confirm that you have the Vision S with a 4.3 inch monitor? I cannot see what size screen you have in the photo you provided.
Becky D.
5/2/2022
I ordered a 7 inch monitor.
This appears to be good quality and shipping was fine. Unfortunately, it doesn't fit the 4.3" monitor that I bought at the same time. I expected, since I was ordering all three parts (4.3" Monitor, cord and mount) at the same time that this would have been verified before shipping as it should have been obvious that the mount was intended to go with the ordered monitor. I am reaching out for a replacement that will fit the monitor I ordered.
Jenny N.
9/29/2022
This suction cup mounted is a fit for the 4.3 inch monitor. I checked and I see that it looks like you received the wrong part and we have shipped a replacement to you.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Karyl K.
5/31/2025
After a year I must say, this mount has held up very well for our Furrion RV rear camera monitor. I continue to recommend!