Tandem Axle Trailer Hanger Kit For 3" Slipper Springs

Question

Question:

Do you sell the Lippert axle spring hanger angle brackets. I have the lippert drawing and the drawing # is 103727 not sure if that is Lipperts part # Thanks

asked by: Brian

0

Expert Reply:

I checked our website, and it doesn't look like we carry the part you're referring too.

We do carry a couple axle hanger kits like the Dexter Tandem-Axle Trailer Hanger Kit for 3" Slipper Springs # HAP-103-203-03. Depending on what you need, we might have what you're looking for.

expert reply by: Bryce D

0

Answer 1

You are correct. The Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double-Eye Springs #K71-448-00 you were looking at is 4" tall meaning it slightly will lift your trailer. These equalizers are slightly shorter at…

view full answer...

Answer 2

You could use a taller equalizer but you would also need to use taller front and rear hangers as well. Everything will have to be raised equally so if you go up 2 inches in one spot you have to go up 2 inches in all spots. If you do not raise it at…

view full answer...

Answer 3

Excellent question, and the difference between the two kits comes down to the dimensions of the equalizers. What you will want to do is match up the size of your equalizer with the size of the equalizer in these kits. - 6" Long, 4" Tall…

view full answer...

Answer 4

Hello Robert, thanks for reaching out. If you have grease zerks on your spindles, you would want to slowly add grease until it starts coming out of the spindle or the front of the hub. Do not force too much grease in and overfill or you can blow out…

view full answer...

Answer 5

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hey Randy thanks for the information! Here are the parts you'll need to add a brake controller to your 2006 Dodge Ram 1500 with a factory 4-Way connector: Brake Controller and Custom Fit Wiring Harness - Curt TriFlex NEXT item #C43GV 7-Way…

view full answer...

Answer 8

Hey David, we have everything we need to flat tow your 2006 Dodge Ram 1500 4WD but the first thing you need is a base plate kit like the Blue Ox part #BX1988 which I like because in my experience the Blue Ox kits are just really well made and easier…

view full answer...

Answer 9

If your 2006 Dodge Ram 2500 already has the B&W Underbed Kit #BWGNRK1308-5W installed, then the B&W Companion #BWRVK3400-5W is definitely the best option for towing a fifth-wheel trailer. The Companions are considered by many to be the best…

view full answer...

Answer 10

You sure do Greg! Which is why the MORryde X-Factor Crossmember for Standard Frame Hangers item #MR33WR comes with longer suspension bolts. These bolts will replace the ones currently being used on your trailer's spring hangers. The X-Factor…

view full answer...

Answer 11

On the 2006 Dodge Ram 1500 that came with either a factory 4-Way or 7-Way trailer connector the receptacle to plug in a brake controller with a harness such as #3020-P will either be on top of or along the side of a white rectangular box back along…

view full answer...

Answer 12

Hey John! With the CRE3000 on your Reflection you need the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR. The same crossmember will be used on all three sets of hangers. The one thing I would do is take a look under your trailer to…

view full answer...

Tandem Axle Trailer Hanger Kit For 3" Slipper Springs

Product Page this Question was Asked From

Continue Researching