Base Dimensions and Mounting Hole Location of MaxxTow MaxxHaul Hand Winch # MT50156

Question

Question:

Hi I have a MaxxTow MaxxHaul Hand Winch - 20foot Strap - 1,200 lbs Item # MT50156. Long story short I ped it while it was attached to its new mounting frame and I broke a couple pieces. can I get replacement parts or is the situation where I should just get another complete unit? Also, Do you have a layout for the bolt pattern for mounting? Im having mounting parts fabricated, so if I could skip transferring the holes etc. that would be nice. Thanks for the Help!

asked by: Kelby D

1

Helpful Expert Reply:

You will want to replace your MaxxTow MaxxHaul Hand Winch # MT50156 as there are no spare parts available for it.

I created an image with the dimensions for the base with the mounting holes. The base is 5-1/2" long and 3-1/2" wide. There are 3 elongated mounting holes on the base. The 2 mounting holes near the strap end are separated 2" on center while the 3rd hole is centered on the base 3-5/8" to the center from the centerline of the 2 other mounting holes.

expert reply by: Bud M

1

Base Dimensions and Mounting Hole Location of MaxxTow MaxxHaul Hand Winch # MT50156
(click to enlarge)

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Base Dimensions and Mounting Hole Location of MaxxTow MaxxHaul Hand Winch # MT50156

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching