Replacement Hub for Trailer with 84 Spindle Dimensions

Question

Question:

Thank you could you also suggest the electric brakes to do with the hubs

asked by: Scott

0

Expert Reply:

Your pictures didn't make it through, could you email them to me?

expert reply by: Jameson C

0

spindle dimensions
(click to enlarge)

Scott

3/2/2022

See attached picture.

Jameson C.

3/2/2022

Thanks, based on those dimensions you have a 84 spindle which is what 3,500 lb trailer axles have. So you could use the hub part # AKHD-545-35-K which is even pre-greased and ready to install. This has a 5 on 4-1/2 inch bolt pattern which is very common for trailer wheels. I am not sure what size you'd like but I attached a link to a page that has all of the wheels we offer with this bolt pattern.

Scott

3/3/2022

Thank you could you also suggest the electric brakes to do with the hubs

Jameson C.

3/3/2022

For a set of self-adjusting brake assemblies to use with the # AKEBRK-35-SA would be a great option.

Answer 1

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 2

The hub center's outer diameter of the Dexter Hub and Drum #84546UC3 measures 2.59 inches. A rim with a 3.19 pilot diameter, like #AM20352 will fit onto the Dexter hub because the wheel is lug-centric and not hub-centric.

view full answer...

Answer 3

You were given some correct information. The new trailer wheels you purchased that have a larger pilot hole will still be compatible with your hubs in terms of being properly centered. The key is indeed the coned lug bolts, such as #RG02-020. These…

view full answer...

Answer 4

It sounds like you have a traditional spindle size for a 3500 lb axle. For your bearing kit, I recommend the Bearing Kit for number 84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal #BK2-100 based on your dimensions. This is the most common…

view full answer...

Answer 5

I went out to our warehouse to measure the Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 6 on 5-1/2 #84655UC1 for you. It has an outside bore diameter of 3.09 inches that the center of the wheel will fit over. I've attached a photo to…

view full answer...

Answer 6

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 7

It sounds like you're asking about the torque spec for the castle nut on your 3,500 lb axle. There is no specific torque rating when installing the castle nut on any axle. You want to run the nut down until there is no side to side play in the…

view full answer...

Answer 8

Hello Mike. It sounds like you are wanting to add electric brakes to your boat trailer that currently has no brakes. This is possible, but you will first need to make sure that your axle is equipped with a brake flange at the base of the spindle. The…

view full answer...

Answer 9

The 3rd wire on a 3-wire breakaway switch like the Hopkins LED Breakaway Switch with 7" Lead Wires #HM20059 gets grounded to the trailer frame or tied in to the main ground on your trailers tongue. The only difference between a 2-wire and 3-wire…

view full answer...

Answer 10

For your Hopkins LED Breakaway Switch part #HM20059 the led indicator should only be lit when the breakaway pin is pulled, and should be solid. When the pin is inserted and the trailer hooked up it should not be on at all. If you do not have the…

view full answer...

Answer 11

With an Enclosed Trailer Ramp Spring #ERS120D81 when the door is lowered it will pull the cables which will turn the pulleys and put tension on the springs. The cables could not be detached with the ramp door lowered because the springs would…

view full answer...

Answer 12

The #FR93FR, FWH09A-AM, FWH09A-1-A are all the same Furrion Tankless Water Heater. since you're wanting to reuse the door and wall controller you'll want the #FR93FR to save yourself the money on the door. It will however still come with the…

view full answer...

Replacement Hub for Trailer with 84 Spindle Dimensions

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching