Replacement Grease Seal for Shorlandr with Manual that Calls for TCM127194TB

Question

Question:

My Shorlander trailer manual lists seals TCM12192TB and TCM127194TB, do you know the difference between these parts or are they equivalent

asked by: David K

0

Expert Reply:

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part # RG06-010, which is a double-lip seal sold as a pair and will work for you. Its outer diameter is 1.983-inches and its inner diameter is 1.249-inches. This is the same as the other number you mentioned.

expert reply by: Jameson C

0

Answer 1

Hey Steven. What's your question? If your 2,200 lbs axle has a 1-1/16" BTR Spindle you'll have the same inner and outer bearing size item #L44649. You'll need a seal with a 1.25" inner diameter. You can get all of these parts…

view full answer...

Answer 2

The difference between the single lip and double lip seals is that the double lip grease seal will have two rubber lips that are in contact with the spindle. The double lip grease seals are usually used in marine applications to give a better seal…

view full answer...

Answer 3

I wish we could help but none of our hubs fit a spindle that is 1-1/4 inch in diameter all the way across. If instead the spindle was 1-1/16 inch diameter for both bearings you'd want the part #8-258-50UC1-EZ which is standard for a 2,200 lb…

view full answer...

Answer 4

Hey Dave, For your application I recommend picking up the Timken Replacement Bearing and Race Set - L44649 and L44610 #TMK23VR, and the Timken Grease and Oil Seal #TMK48ZR. We don't have a kit that has all of these parts together, which is why I…

view full answer...

Answer 5

If you only have the nut and a washer but no cotter pin or retaining type washer on the end then that isn't correct and you want to get a piece to help prevent that nut from backing off. If you have a setup like the Spindle Nut Kit for EZ Lube…

view full answer...

Answer 6

Hey Dave, what you gave me is enough info to get you replacement bearings. The grease seal 471750 matches the part #TMK48ZR. For a Timken replacement for the L44610 part number you'd need #TMK63VR. Then for a bearing for the L44649 you'd want…

view full answer...

Answer 7

Without knowing which specific part number hubs you're speaking of, it's hard to say what the differences are, but I can give some generalities that might help answer your question. The specific hub you'll need will depend on the diameter…

view full answer...

Answer 8

It would be great if trailer makers kept detailed records of all of the component parts used in their products, but this is rarely the case. No worries, though. You just need to match up a few features. Once you match those features it is easy to…

view full answer...

Answer 9

It sounds like you are going to need the Timken Grease Seal #TMK36ZR. This has the 1.250" inner diameter with 1.983" outer diameter and the width is 0.406". You will want to verify this will fit your hub using a Caliper #PTW80157.

view full answer...

Answer 10

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 11

When installing a seal at the back of a hub the outer part of the seal will need to be flush with the hub. I have linked a video that should help. You could watch the whole video or fast forward to the 1 minute, 50 second mark to see the seal…

view full answer...

Answer 12

For idler hubs, you will want the Trailer Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 #AKIHUB-545-2-1K or the 4 on 4 inch bolt pattern #AKIHUB-440-2-1K. This is a standard BT8 spindle. I've attached an installation video to assist as well as an…

view full answer...

Replacement Grease Seal for Shorlandr with Manual that Calls for TCM127194TB

Product Page this Question was Asked From

Continue Researching