Bearings And Seals For Superior 1510-L Trailer With 2,000 lb GVWR
Updated 11/17/2025 | Published 12/08/2024
Products Featured in This Question
Question:
I have a Superior 1510-L trailer with a GVWR of 2000 Lbs. The bearings that came out have a 1.0625 ID, little over 1.75 OD and approx. 1 19/32 width. There were no seperate races, the grease seal is approx. 1.95 OD and 1.25 ID. The spindle itself has 1 outer threads, 1.0625 shaft, 1.25 Seal and 1 5/8 main shaft thickness. The trailer itself is 5 wide X 10 long. Can you help me figure out what kit I should purchase? Many thanks
asked by: John P
Expert Reply:
Hey John, thanks for reaching out. It sounds like you need the Timken Grease Seal # TMK36ZR which is I.D. 1.250" / O.D. 1.983". As far as the bearings it sounds like your hub uses the L44649 bearing which is the 1.063" ID. This goes with the L44610 race which is 1.98" OD. There has to be a race in your hub for the seal to ride on so please do measure you race and verify it is the 1.98" OD. We do not have a kit that comes with all of these so you will need to get them separately. Here is what I recommend:
- Timken Replacement Bearing and Race Set - L44649 and L44610 # TMK23VR
- Timken Grease Seal - Single Lip - I.D. 1.250" / O.D. 1.983" - 203029 # TMK36ZR
Product Page this Question was Asked From
Replacement Trailer Wheel Bearing Kit - BT8 Spindle, Bearings L44643, Races L44610, Seal 34823
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44643
- Race L44610
- 2000 lbs Axle
- 2500 lbs Axle
- etrailer
more information >
Continue Researching
- Search Results: castle nut
- Search Results: bearing seal
- Search Results: spindle nut
- Search Results: 5 lug trailer hub
- Shop: Timken 203029 Grease Seal - Single Lip - I.D. 1.250" / O.D. 1.983" for 2K to 2.5K Axles
- Video: Checking Out the Timken Grease Seal
- Shop: Dexter Bearing Kit for 1-1/16" BTR Spindle - Bearings L44643/L44643, Races L44610/L44610
- Video: An In-Depth Look at the Timken Grease and Oil Seal
- Video: A Closer Look at the Double Lip Grease Seals (pair)
- Video: Review of Dexter Trailer Bearings Races Seals Caps - Bearing Kit 1-1/16 Inch BTR Spindle - DX59UR
- Video: Review of CE Smith Trailer Axles - Axle Spindle Parts - CES52QR
- Video: What to Know About the Trailer Hub Assembly
- Shop: Grease Seal - Double Lip - I.D. 1.249" / O.D. 1.983" - 2,000-lb to 2,200-lb Axles - Qty 1
- Video: Installing the etrailer Trailer Hitch Receiver on a 2026 Chevrolet Equinox
- Shop: Cotter Pin - 1/8" Thick x 1-3/4" Long
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Shop: Trailer Hub Assembly - 2,200-lb E-Z Lube Axle - 5 on 4-1/2 - 13" - 15" Wheels - Galvanized
- Shop: Karrier ST175/80R13 Radial Trailer Tire with 13" Galvanized Wheel - 5 on 4-1/2 - Load Range D
- Shop: Trailer Idler Hub Assembly for 2K Axles - 10" to 12" Wheels - 5 on 4-1/2 - Pre-Greased
- Q&A: Recommended Bearing Kit for 1-1/16" BTR Spindle
- Q&A: How Far in a Trailer Hub Should the Grease Seal Go
- Q&A: Can 1/4 inch Thick Trailer Hub Grease Seal be Replaced with a 1/2 inch Thick Seal
- Q&A: Timken Replacement Bearing Solution for Setup with Part Numbers L44649 471750 L44610
- Q&A: Does Trailer Hub Seal Width Need to be Measured to Pick Out Replacement
- Q&A: Recommended Idler Hub Assembly for 1-1/16 Inch Diameter Spindle With Seal 1-1/4 Inches at Spindle
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Search Results: locks
- Search Results: l44649 bearing kit
- Search Results: timken l44649
Jesse M.
11/17/2025
Hey John, did the Timken bearing and seal setup end up matching your Superior 1510-L trailer? Knowing how the fit turned out could really help others trying to replace similar parts.