Dimensions Of etrailer Round, Pipe Mount Swivel Jack w/ Footplate # TJP-7001-B

Question

Question:

What is the measurement from center of mount to the top of jack? Thanks

asked by: Cliff

1

Helpful Expert Reply:

The Round, Pipe Mount Swivel Jack w/ Footplate # TJP-7001-B is 6" from the center of the mount to the highest point on the jack with the handle folded.

expert reply by: Bud M

1

etrailer Round, Pipe Mount Swivel Jack w/ Footplate # TJP-7001-B Height From Mounting Point
(click to enlarge)

Dimensions of etrailer Round, Pipe Mount Swivel Jack w/ Footplate # TJP-7001-B
(click to enlarge)

Answer 1

Hey Robert, thanks for the information. To add rear stabilizer jacks to your dump trailer, I recommend a pair of the Square Direct Weld Jack w/ Footplate item #TJD-8000S. This jack has a 7,000 lbs capacity and is sold individually so you'll need…

view full answer...

Answer 2

The Square Direct Weld Jack part #TJD-8000S is designed as a direct weld-on jack. The outer tube is made to be welded directly to the side of the trailer. If you're looking for a pipe mount, the Square Pipe Mount Swivel Jack part #TJDP-7000-B is…

view full answer...

Answer 3

The etrailer jack part #TJP-7002-B that you referenced would be a great replacement for the Atwood you have now. It's a similar jack that uses a pipe mount, a topwind, and has plenty of weight capacity at 7,000 lbs.

view full answer...

Answer 4

Yes, you will be able to weld on the 2" Male Pipe #TJP-IP916 which is included with the Round, Pipe Mount Swivel Jack #TJP-5001-Z on your 2" tall frame.

view full answer...

Answer 5

You can place the pin on the Square Pipe Mount Swivel Jack w/ Footplate #TJDP-5000-FLB either way when it is holding weight. The weight of the trailer will be bearing down on that pipe mount bracket while the pin just keeps the trailer jack in place.…

view full answer...

Answer 6

It sounds like you're looking for a replacement jack like the Round, Pipe Mount Swivel Jack w/ Footplate #TJP-7001-B. This comes with a round, 2" tube piece that you would normally weld onto the trailer for the installation but if you…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Dimensions Of etrailer Round, Pipe Mount Swivel Jack w/ Footplate # TJP-7001-B

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching