Does Square Pipe Mount Swivel Jack w/ Footplate Rotating Pin Need to Be Place Horzontal or Vertical

Question

Question:

Which way do you place the safety pin when the jack is holding weight, horizontally or vertically?

asked by: Steven C

0

Expert Reply:

You can place the pin on the Square Pipe Mount Swivel Jack w/ Footplate # TJDP-5000-FLB either way when it is holding weight. The weight of the trailer will be bearing down on that pipe mount bracket while the pin just keeps the trailer jack in place. The only way there will be any significant amount of pressure placed on the pin is if the jack is forced to rotate while the pin is in place (like if you drove away with the jack down and hit something).

expert reply by: Jon G

0

Answer 1

First, you are going to need a key for the old locks. The key is needed to depress the tumblers in the locks you have. Otherwise you will not be able to get them out. What is the number on the face of the locks you have? With the key inserted you…

view full answer...

Answer 2

The Square Direct Weld Jack part #TJD-8000S is designed as a direct weld-on jack. The outer tube is made to be welded directly to the side of the trailer. If you're looking for a pipe mount, the Square Pipe Mount Swivel Jack part #TJDP-7000-B is…

view full answer...

Answer 3

To replace the 9/16 inch pull pin for your Pro Series Round Swivel Jack #PS1401480303 you can use the Replacement Pull Pin #BD500243. This includes the pin, chain, and drive screw.

view full answer...

Answer 4

The Square Pipe Mount Swivel Jack #TJDP-7000-B uses the Replacement Pipe for etrailer and Ram Pipe Mount Swivel Jacks #TJP-OP58 which has a 2 inch inner diameter and 2-1/4 inch outer diameter. In the video the description is of the weld-on pipe mount…

view full answer...

Answer 5

The outer diameter of the pipe mount that comes with the Pro Series Round, Pipe-Mount Swivel Jack part #PS1401480303 is 2". It uses a 5/8" diameter pin.

view full answer...

Answer 6

The etrailer jack part #TJP-7002-B that you referenced would be a great replacement for the Atwood you have now. It's a similar jack that uses a pipe mount, a topwind, and has plenty of weight capacity at 7,000 lbs.

view full answer...

Answer 7

The Round, Pipe Mount Swivel Jack w/ Footplate #TJP-7001-B is 6" from the center of the mount to the highest point on the jack with the handle folded.

view full answer...

Answer 8

Yes, you will be able to weld on the 2" Male Pipe #TJP-IP916 which is included with the Round, Pipe Mount Swivel Jack #TJP-5001-Z on your 2" tall frame.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Does Square Pipe Mount Swivel Jack w/ Footplate Rotating Pin Need to Be Place Horzontal or Vertical

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching