Can the Square Direct Weld Jack Be Mounted As a Swivel Jack

Question

Question:

can you weld a pipe on the housing to make this a pipe swivel mount jack? Thanks,

asked by: Jimmy R

0

Expert Reply:

The Square Direct Weld Jack part # TJD-8000S is designed as a direct weld-on jack. The outer tube is made to be welded directly to the side of the trailer. If you're looking for a pipe mount, the Square Pipe Mount Swivel Jack part # TJDP-7000-B is very similar and what we'd recommend using.

expert reply by: Conner L

0

Answer 1

Yes, you will be able to weld on the 2" Male Pipe #TJP-IP916 which is included with the Round, Pipe Mount Swivel Jack #TJP-5001-Z on your 2" tall frame.

view full answer...

Answer 2

You can place the pin on the Square Pipe Mount Swivel Jack w/ Footplate #TJDP-5000-FLB either way when it is holding weight. The weight of the trailer will be bearing down on that pipe mount bracket while the pin just keeps the trailer jack in place.…

view full answer...

Answer 3

The Round, Pipe Mount Swivel Jack w/ Footplate #TJP-7001-B is 6" from the center of the mount to the highest point on the jack with the handle folded.

view full answer...

Answer 4

The etrailer jack part #TJP-7002-B that you referenced would be a great replacement for the Atwood you have now. It's a similar jack that uses a pipe mount, a topwind, and has plenty of weight capacity at 7,000 lbs.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Can the Square Direct Weld Jack Be Mounted As a Swivel Jack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching