Side-Door Bar Lock Assembly With Offset Handle Availability

Question

Question:

I am looking for a bar lock assembly similar to your part #3057-55 but I need the handle to be offset instead of centered. Do you have something like that? I have not been able to find it. Thanks

asked by: Marty H

0

Expert Reply:

For an offset handle you will want to use the Cam-Action Lockable Door Latch Kit # PLR3057 that you can use to attach to a length of schedule 40 3/4" pipe. You will be able to have the hinges and latch welded in place where you need to ensure that the handle is where you want it.

expert reply by: Bud M

0

Answer 1

The part number you list is for a Dometic BriskAir II. My recommendation is the 15,000 Btu Advent Air Replacement RV Air Conditioner for Dometic Setup w/ Start Capacitor, #ACDOM150B. This is designed for replacing a currently installed Dometic AC…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 11

Hey Neil. The 18,000 Btu Furrion Chill Cube RV Air Conditioner item #LC34DX fits a 14-1/4" x 14-1/4" cutout which is pretty standard on RV's. If you meant to write Dometic instead of domestic then yes it'll fit in your existing…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Side-Door Bar Lock Assembly With Offset Handle Availability

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching