Replacement Handle for Shelby Trailer Jack

Question

Question:

I have a shelby trailer jack. It needs a new crank handle. Cant find a model number. 12 tooth gear and the pin hole on the handle is about 1 3/4 in from the end. Do you have a kit for this?

asked by: Michael D

0

Expert Reply:

For a replacement handle you need the Top Wind Trailer Jack Handle # JP02-010. This is a topwind handle that fits Atwood, Shelby, and Fulton Jacks.

expert reply by: Robin H

0

Answer 1

You'd have to remove the PAL nut of the old handle first to install the part #HDKB-BLK. Simply grab the nut with a pair of pliers and bend it off. Once you apply a bit of pressure, the nut will bend which will allow you to easily remove it.

view full answer...

Answer 2

Since Shelby is no longer in business, and jack handles are not universal, what that means is there isn't a replacement handle available, so your only option is to get a brand new jack. Since the Shelby is a weld-on jack, the best option we have…

view full answer...

Answer 3

I went out to the warehouse and measured the inner diameter of the cap included with Replacement Black Handle #HDKB-BLK. It is approximately 1/2 inch.

view full answer...

Answer 4

The Top Wind Trailer Jack Handle part #JP02-010 will be a direct replacement for your Shelby 5793 A-Frame Trailer Jack.

view full answer...

Answer 5

For your Shelby 5856A boat trailer, I recommend the Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels - Sidewind - 12" Lift - 1,500 lbs #FXPD15L. This jack has zinc plating for corrosion resistance and durable poly wheels. For the single…

view full answer...

Answer 6

The Fulton Bolt-Thru Swivel Marine Jack #FXP15W is a bolt through replacement option for you. This is designed to use a welded plate like the Jack Mounting Bracket for Fulton Marine Jack #P9012-00. It appears like you have a bolt that goes into a…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Handle for Shelby Trailer Jack

Product Page this Question was Asked From

Continue Researching