How Does Grommet for Optronics Taillight # A91GB Install

Question

Question:

Looking at side clearance led lights to replace Miro-Flex 349. How do the grommets mount to camper?

asked by: Paul A

0

Expert Reply:

If you want to see how the grommet part # A91GB installs check out the install video link I attached to this page. Basically these fit into a cut out hole on the trailer fender.

expert reply by: Jameson C

0

Answer 1

Hello Travis, thanks for reaching out. We do have a grease seal that is very close to the dimensions you listed, although we don't have an exact match. Take a look at the following: - Grease Seal 29031 #29031 This is 3" OD, 1.875" ID…

view full answer...

Answer 2

I am not aware of a bolt-on version of the Buyers Products Weld-On Safety Chain Retainer part #3375471000. However, if all you were wanting to do is mount your safety chains to the tongue of your trailer then you will just simply do so by running a…

view full answer...

Answer 3

In order to find the correct grease seal to use with bearing #2788 you would need to use a digital caliper such as #PTW80157 to measure the inner and outer diameter of your current grease seal to the thousandths of an inch. Bearing #2788 is often…

view full answer...

Answer 4

So after quite a bit of research it seems that the Trostel 300-156-6 seals you mentioned are quite old and have not been around for some time. The best I could find was that they are 3.00" in outer diameter, and I did manage to find a customer…

view full answer...

Answer 5

There are really two reasons to replace a grease seal, if they are damaged or worn and leaking grease then that is an obvious factor. If you are replacing bearings it is usually best to replace the grease seals as well because although they may still…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How Does Grommet for Optronics Taillight # A91GB Install

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching