Replacement Latch Bar Assemblies For A BAKFlip MX4 Tonneau Cover

Question

Question:

I need the rear latch bar assembly for a bakflip mx4. Do you have it?

asked by: Kevin

0

Expert Reply:

If you're needing the latch bar assembly for the tailgate side of your MX4 you'll need the Replacement Tailgate Latch Bar Assembly for BAKFlip Hard Tonneau Covers # BAK65RV.

If you're needing the latch bar assembly for the cab side of your MX4 you'll need the Replacement Cab Latch Bar Assembly for BAKFlip Hard Tonneau Covers # BAK47AV.

expert reply by: Kevin C

0

Eugene

12/29/2024

The video with a lady installing a bakfli mx4 on a 22tundra the brackets that goes in the top cap rails to drop down the oem rails to use the knob tie downs they are aluminum like a s shape with 2 holes in them I will buy them I need them

Answer 1

Thanks for that info, and I was able to find that 35830102 is the part number for the Latch Pocket Cover for the Extang Solid Fold 2.0 tonneau cover. We do have that part available, which is the following: - Replacement Latch Pocket Cover for Extang…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Replacement Latch Bar Assemblies For A BAKFlip MX4 Tonneau Cover

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching