Replacement Parts for MaxxAir MaxxFan Plus Roof Vents

Question

Question:

Hello, Not sure if it is the vent or just the switch/controller that is bad. nothing works using the switch on the wall but I have 12 volt going to the fan. could it be the controller? This fan also has a rain sensor on it. Do you have any idea what the problem would be.

asked by: Raymond C

0

Expert Reply:

If you have 12 volts going to the fan it is motor. You will need the Replacement 12-Volt Variable Speed Fan Motor for MaxxAir MaxxFan RV Roof Vents item # MA10-20968. If the voltage isn't going to the motor than it could be the controller which is item # MA10A04751KS. We offer both of these parts in the Replacement MaxxFan Plus 10-Speed Roof Vent with Smoke Lid item # MA99FR.

expert reply by: Jerred H

0

Answer 1

I determined that your Ventline exhaust fan v2525 is a northern breeze model and unfortunately we do not carry a replacement motor. I recommend Replacement Roof Vent for MaxxFan Plus Roof Vent w/ 12V Fan - Powered Lift - 10 Speed - Smoke Item…

view full answer...

Answer 2

I can't find any info on the part number you mentioned but could I maybe see a picture of the and/or know what specific fan you have installed?

view full answer...

Answer 3

Since multiple MaxxAir Fans have the same features that you listed it's honestly best to first determine the exact model number you have before purchasing anything and end up not having it be compatible. I've listed below all the available…

view full answer...

Answer 4

I did some checking and for the MaxxAir the correct replacement circuit board is the #MA39FR.

view full answer...

Answer 5

Yes, the Replacement Printed Circuit Board for MaxxAir Powered Lift RV Roof Vents w/ Exhaust Only Fan #MA39FR is the correct replacement circuit board for your 8501 model.

view full answer...

Answer 6

The 10B21275KE part #MA39FR replaces the 10-21275KE you mentioned as well so if you had an older model number you could use it in same application.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Parts for MaxxAir MaxxFan Plus Roof Vents

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching