Brake Magnet Clip Replacement for Trailer Brake Assembly

Question

Question:

Looking for the correct ones.

asked by: JAY S

0

Expert Reply:

Thanks for the picture of your brake magnet clips. Based on seeing them the correct replacement is the part # 027-005-00.

expert reply by: Jameson C

0

Brake Assembly with Magnets
(click to enlarge)

Answer 1

The #BP19-001 retaining clips are designed to fit the Dexter 7-inch brake magnets. Our contact at Dexter said the BP19-001 will work on both the 7-inch round and the 10-inch oval magnets. The replacement magnet clip, part #BP19005 will fit 10, 12,…

view full answer...

Answer 2

The brake magnet is held onto an electric braking assembly with a clip. It is not impossible for these to work themselves out over time so I would make sure that you still have the clip in place. The clip is located inside the center of the magnet…

view full answer...

Answer 3

I spoke with my contact at Redline about the availability of the retaining clip for the Dexter 7-inch brake magnets. He said you can use the Magnet Retainer Clip, part #BP19-001 , on the Dexter 7-inch round magnets. These retaining clips will work on…

view full answer...

Answer 4

For your brake magnets, I recommend the Replacement Magnet Clips for Electric Brake Assemblies (Qty 4) #BP19005 which are designed for that style magnet.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Brake Magnet Clip Replacement for Trailer Brake Assembly

Product Page this Question was Asked From

Continue Researching