Replacement Brake Assembly Magnet Clips for Dexter 7 inch Brake Assemblies

Question

Question:

I bought Replacement Trailer Brake Magnet Kit for 7inch Brake Assemblies Item #AKBRKR-M7... the magnet retaining clips have come off. I see some clips for 10inch brakes, but they look too large, Can I buy the clips that come with the 7inch brakes?

asked by: Steve L

0

Expert Reply:

I spoke with my contact at Redline about the availability of the retaining clip for the Dexter 7-inch brake magnets. He said you can use the Magnet Retainer Clip, part # BP19-001 , on the Dexter 7-inch round magnets. These retaining clips will work on both the 7-inch round and the 10-inch oval magnets.

expert reply by: Jameson C

0

Answer 1

The #BP19-001 retaining clips are designed to fit the Dexter 7-inch brake magnets. Our contact at Dexter said the BP19-001 will work on both the 7-inch round and the 10-inch oval magnets. The replacement magnet clip, part #BP19005 will fit 10, 12,…

view full answer...

Answer 2

It sounds like you're looking for the Adjuster Plugs for 7", 10", and 12" Brake Assemblies #BP10-220. These adjuster plugs will fit Dexter 7" x 1-1/4", 10" x 1-1/2", 10" x 2-1/4", and 12" x…

view full answer...

Answer 3

The brake magnet is held onto an electric braking assembly with a clip. It is not impossible for these to work themselves out over time so I would make sure that you still have the clip in place. The clip is located inside the center of the magnet…

view full answer...

Answer 4

For your brake magnets, I recommend the Replacement Magnet Clips for Electric Brake Assemblies (Qty 4) #BP19005 which are designed for that style magnet.

view full answer...

Answer 5

Thanks for the picture of your brake magnet clips. Based on seeing them the correct replacement is the part #027-005-00.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Brake Assembly Magnet Clips for Dexter 7 inch Brake Assemblies

Product Page this Question was Asked From

Continue Researching