Draw-Tite or Curt Hitch Receiver for 2022 Acura MDX

Question

Question:

Trying to decide between draw tight and curt trailer hitch for MDX 2022. They look pretty similar other than a few slight differences. Could you explain why the installation on the curt is easy and 30 minutes and the installation on the draw tight is moderately difficult and 50 minutes?

asked by: Greg T

0

Expert Reply:

I would be happy to help you. The difference in the installation time between the two hitch receiver's on your 2022 Acura MDX is that the Curt item # C22HR sits lower when mounted so it does not requiring trimming of the rear bumper cover. The Draw-TIte item # DT42MR sits higher after installation which requires you to cut a 4" x 3.5" section of your rear bumper cover out. I recommend going with the Draw-Tite hitch receiver item # DT42MR because of its final mounting location after install. It will have a better ground clearance than the Curt and be less conspicuous.

expert reply by: Jerred H

0

Answer 1

Hello Don, thanks for reaching out. Problems with these plug and play harnesses like the Curt #C53MJ are not common, but there are a few things we can check. First make sure the fuses are fully inserted and seated. Also make sure the plug that goes…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" item #C22HR you referenced fits the 2022 Acura MDX regardless of the size of the spare tire. The issue with yours is that the 21 inch wheel will not be able to be remounted after the…

view full answer...

Answer 3

Yes, cutting of the bumper fascia will be required when installing the Draw-Tite #DT42MR on a 2024 Acura MDX. You are basically cutting a 4" x 3.5" rectangle (see the image below). So the instructions are clear on exactly where to cut. I…

view full answer...

Answer 4

I recommend going with the Draw-Tite Max-Frame Trailer Hitch Receiver #DT42MR for your 2022 Acura MDX Type S (this hitch fits all models). We don't have any notes about this interfering with your foot sensor but it isn't uncommon for people…

view full answer...

Answer 5

Yes, the Draw-Tite Max-Frame Trailer Hitch Receiver #DT42MR you mention does in fact fit your 2022 Acura MDX. This hitch has a maximum towing capacity of 6,000-lbs, a maximum tongue weight of 900-lbs, and has a sturdy square tube design that features…

view full answer...

Answer 6

The Acura MDX is the 'sister' vehicle to the Honda Pilot. The MDX and Pilot typically don't have problems with the hitch interfering with the liftgate sensors. I believe you're thinking about the RDX/Honda CR-V which frequently has an…

view full answer...

Answer 7

Hey Richard. The Draw-Tite Hitch item #DT42MR has the same spare tire restrictions as the other two hitches that fit the 2025 Acura MDX. This hitch does require trimming of the rear fascia. I have attached a picture below from the instructions that…

view full answer...

Answer 8

To add a hitch to your 2023 Acura MDX, I recommend the etrailer item #e27KR. This hitch is custom fit and bolts to your Acura with included hardware. This is a class III hitch with a 2" receiver. It has a 6,000 lbs towing capacity and a 900 lbs…

view full answer...

Answer 9

I will be happy to clear up the confusion for you. The Curt Trailer Hitch Receiver item #C22HR you referenced and the Draw-Tite Max-Frame Trailer Hitch Receiver item #DT42MR will only accommodate the 18" spare on your 2022 Acura MDX. These are…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Draw-Tite or Curt Hitch Receiver for 2022 Acura MDX

Products Featured in This Question

Continue Researching