Does Spare Tire Get Removed When Installing Curt Trailer Hitch C15302

Question

Question:

Will the spare tire come down with this hitch

asked by: Kevin D

1

Helpful Expert Reply:

Yes, the spare tire will get lowered - but only temporarily - when you are installing the Curt Trailer Hitch Receiver # C15302.

After you complete the install and torque the bolts down of the Curt Hitch # C15302, you will then raise and reinstall the spare tire so it will ultimately stay put.

expert reply by: Kyle S

1

Answer 1

Curt does not have that measurement available, but you can determine this for yourself by taking some measurements from the underside of your truck. Using the diagram I edited for you, locate the weldnut that would serve as the rear-most attachment…

view full answer...

Answer 2

The Draw-Tite #DT45519 is designed to be used on the 8 foot bed models of the GMC Sierra and will not fit the short bed models. That being said, we do have Class V hitches with a 2 1/2 inch receiver options available for your short bed truck. The…

view full answer...

Answer 3

The #14108 trailer hitch is not a fit for your Silverado but we do offer a hitch that will work for you. I recommend the Draw-Tite Ultra Frame Trailer Hitch Receiver, part #41944. This is a Class V hitch and it has a 2 inch receiver opening. This is…

view full answer...

Answer 4

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 5

With Curt Trailer Hitch Receiver #C15302 installed on a 2003 Chevy Silverado 2500 short bed the hitch will be in the same position as a factory hitch or at least within a fraction of an inch. By that I mean the receiver will be right under the rear…

view full answer...

Answer 6

According to my technical contact at Curt Manufacturing their Class V Hitch #C15302 will fit your truck, if it were equipped with a standard 265mm wide spare, with about an inch of extra space. The hitch was engineering with this tire size in mind.…

view full answer...

Answer 7

I had our warehouse measure the Curt Trailer Hitch Receiver #C15703 you were looking at, and has an overall width of 40-5/8", overall length of 29". The distance between the vertical mounting holes is 14-1/2" center to center, and the…

view full answer...

Answer 8

In regards to the Curt Trailer Hitch Receiver part #C15302 which is a fit for a 2001 Chevrolet Silverado 2500 HD - 6-1/2 Foot Bed, there are only two factory weld nuts in the frame which get reused, they are the two closest to the bumper. The other…

view full answer...

Answer 9

It is, I went and measured the distance from the mounting flanges of a Curt Hitch part #C15703 to the cross tube that we have in stock and found that it measures right at 6 inches. I attached an install video for you to check out as well.

view full answer...

Answer 10

I went to the warehouse and measured the Curt Trailer Hitch Receiver, part #C15703. I have attached a photo of the trailer hitch and have noted the dimensions you can check out. This is a Class V trailer hitch and it has a 2-1/2 inch receiver…

view full answer...

Answer 11

I did some checking and there is a Curt Class V hitch that fits your 2005 Chevy Silverado 1500HD but it is not #C15302. Instead you can use #C15323. Curt does confirm this fits the 1500HD models (as well as 2500LD models). I have linked a video…

view full answer...

Answer 12

We haven't had the chance to install the Curt Class V Trailer Hitch Receiver #C15703 on the 2008 Chevy Silverado 2500 so I don't have exactly how far beneath the bumper the receiver will sit, however I did go out to our warehouse to take a…

view full answer...

Does Spare Tire Get Removed When Installing Curt Trailer Hitch C15302

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching