Roadmaster Rear Anti-Sway Bar for 2019 Ram 3500 DRW

Question

Question:

Can you please confirm the correct part number for your roadmaster anti-sway bar for a 2019 Ram 3500 “Dually”

asked by: Scott

1

Helpful Expert Reply:

I contacted Roadmaster to verify that the Rear Anti-Sway Bar, # RM73FR is a confirmed fit for the 2019 Ram 3500 be it DRW or SWR. They confirmed this part is the correct for either type.

expert reply by: Michael R

1

Answer 1

The TorkLift StableLoad Suspension Upgrade w Quick-Disconnect #TLA7310S should fit just fine with the Air Lift air bag kit and RAS on your 2021 Ram 3500. My concern though is that you've either already worn out the factory suspension on your…

view full answer...

Answer 2

Rene, you unfortunately are not going to be able to use both air bags and SumoSprings like #SS68RR at the same time. The air bags fit inside the coil springs on the bag so there would not be room to also have the SumoSprings. Even if you were able to…

view full answer...

Answer 3

No, it won't and it's because of the exhaust. The Hellwig Big Wig Rear Anti-Sway Bar item #HE24MR will only work on the diesel models of the 2024 Ram 3500. It is not compatible with your 6.4 Hemi model. The Roadmaster Rear Anti-Sway Bar item…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Roadmaster Rear Anti-Sway Bar for 2019 Ram 3500 DRW

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching