Exact Measurements for Curt and Draw-Tite Hitch Receivers for a 2005 Dodge Sprinter

Question

Question:

On the 2005 Dodge sprinter 2500 Your claim is it will fit a 2500 or a 3500 but a dual wheel truck has a different width frame I’ve already ordered one from a different vendor and it is not right I would like the measurements to confirm that it will fit my single wheel 2005 Dodge sprinter with a step bumper

asked by: Steve

0

Expert Reply:

I would be happy to help you. We have those items and I was able to get the measurements for you. I have attached pictures detailing the specific dimensions you have asked for. The Curt Hitch Receiver Item # 13250 fits the 118 inch wheelbase with single rear wheels,140 inch wheelbase with single rear wheels, and 158 inch wheelbase with single rear wheels on 2005 Dodge Sprinters. The Draw-Tite Hitch Receiver item # 75210 fits 2005 Dodge Sprinters with a 140 inch wheelbase with single rear wheels and the 158 inch wheelbase with single rear wheels. The difference in measurements between the two hitch receivers is the mounting positions. The Curt item # 13250 mounts inside the frame. The Draw-Tite item # 75210 attaches outside the frame.

expert reply by: Jerred H

0

75210 hitch dimensions 1
(click to enlarge)

75210 Hitch Dimensions 2
(click to enlarge)

Curt13250 hitch receiver
(click to enlarge)

Curt13250 Hitch Dimensions2
(click to enlarge)

Answer 1

The spare tire retainer would almost certainly interfere with installing the #75210, but we do have a hitch that is positioned a bit differently so it would fit perfectly. The Curt #13250 class III hitch will avoid the spare tire retainer, as shown…

view full answer...

Answer 2

Yes, we have the Draw Tite hitch part #75210 as a confirmed fit for your 2004 Freightliner Sprinter 2500 that has the factory step bumper. Draw Tite states that on vehicles with factory step bumper, bumper mounting brackets will be re-attached at…

view full answer...

Answer 3

Hi Tl, I checked each of the hitches that fit your 2005 Sprinter, and they do all require relocating the spare tire. That's true for both the Class III Curt Trailer Hitch #13250 and Class IV Curt Trailer Hitch #14250.

view full answer...

Answer 4

The Curt Class IV Trailer Hitch Receiver, #14250, will fit your 2006 Dodge Sprinter w/ OEM step bumper after some minor modification to the installation hardware. The Curt hitch instructions state that for the factory step bumper models, the corner…

view full answer...

Answer 5

Because we haven't installed either hitch at our facility, I don't have the specific dimensions you're needing, but I can provide a ballpark figure that could be helpful to you. When installed, the top of the receiver tube for either…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver #14250 that you referenced does mount on the inside of the trailer frame, but it does require bolts to be run through from the outside of the frame (see attached picture). You will need to make sure that you have room…

view full answer...

Answer 7

For use with a 2-inch hitch bike carrier I recommend the Curt Class III hitch #13250 as it is a confirmed fit on your 2004 Dodge Sprinter with step bumper and 140-inch wheelbase. Class IV hitch #14250 fits your van too but for use with a bike rack…

view full answer...

Answer 8

The Curt Class IV Trailer Hitch #14250 will only fit if your 2003 sprinter has the 140 inch Wheelbase with Single Rear Wheels. Since you have a 140 inch Wheelbase with Dual Rear Wheels the next best option is the Curt Class III Trailer Hitch #13265…

view full answer...

Answer 9

I am not sure why the RV dealer you went to said you could not safely install a trailer hitch receiver on your 2003 Freightliner Springer 2500 Van with the 158" wheel base and factory step bumper, as the Draw-Tite Max-Frame Trailer Hitch…

view full answer...

Answer 10

I spoke with my contact at Draw-Tite, and he said that as long as your Sprinter frame is 41 inches wide outside to outside and the wheel base is more than 118 inches long, the Draw-Tite Max-Frame Trailer Hitch, item #75210, will fit your 2006 Dodge…

view full answer...

Answer 11

There are 5 versions of the 2006 Dodge/Freightliner Sprinter so to determine if there is a hitch that will fit we have to look at which specific model you have. If you have the 118 inch wheelbase, single rear wheel model you can use #13250 or #14250…

view full answer...

Answer 12

The Curt Trailer Hitch Receiver #13250 will only require spare tire relocation if you have the 118" wheel base model. If your 2003 Dodge Sprinter has the 140" or 158" wheel base you will not need to relocate your spare tire. The…

view full answer...

Exact Measurements for Curt and Draw-Tite Hitch Receivers for a 2005 Dodge Sprinter

Products Featured in This Question

Continue Researching