Grade of Replacement U-Bolt Kit For Blue Ox Weight Distribution

Question

Question:

Are the U-bolts grade 5 or 8? Same with the nuts and washers?

asked by: Allen

1

Helpful Expert Reply:

The hardware and U-bolts are grade 5 for the Blue Ox kit:

- Replacement U-Bolt Kit for Blue Ox Weight Distribution Spring Bars # BLU48FR

expert reply by: Kyle S

1

Answer 1

I recommend using the Replacement U-Bolts for Reese or Pro-Series Weight Distribution Spring Bar Lift Chains #RP58032. This will ensure that you do not have any fit issues with the Reese Dual Cam High Performance Sway Control. The Replacement U-Bolt…

view full answer...

Answer 2

For your Blue Ox SwayPro Weight Distribution w/ Sway Control #BXW1500, you can use the: -Replacement U-Bolt Kit for Blue Ox Weight Distribution Spring Bars #BLU48FR. As far as the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear #TLA8102…

view full answer...

Answer 3

The correct replacement U-bolt kit for the Blue Ox SwayPro weight distribution system is the following: - Replacement U-Bolt Kit for Blue Ox Weight Distribution Spring Bars #BLU48FR

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Christian, welcome to the world of RV-ing! So in addition to the Roadmaster Nighthawk #RM-676 you're also goin to need: - A baseplate kit, like the Roadmaster Direct-Connect Base Plate Kit #RM-521453-5. These attach to the Jeep itself so you…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Grade of Replacement U-Bolt Kit For Blue Ox Weight Distribution

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching