No Power On Charge Line Circuit Of Curt Vehicle Wiring Harness Installed On a 2020 Ford Ranger
Updated 01/11/2025 | Published 08/18/2021
Question:
Why do I not have power on pin 1 have this paired with the curt wireless controller and no power on it either. Have even hooked trailer up put in drive still no power
asked by: Chad S
Expert Reply:
You will want to check the fuse for your trailer charge circuit. As your 2020 Ford Ranger did not include a factory 7-way the fuse may have been left out of the fuse block. You will need to locate the fuse box in your engine compartment to check for the fuses. Your owners manual will help you to identify where the box is and which fuses you will need to check if they are in place and not damaged.
The fuse box you need is located directly behind the battery. You will need to check for a fuse in the slot 73, it should have a 30 amp fuse.
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- No Converter
- No Tow Package
- 7 Blade
- Plug and Lead
- Plug-In
- Visible
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: trailer brake controller
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Video: Install: Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector on a 2020 Ford Ranger
- Shop: Brake Controller
- Shop: Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector
- Search Results: hitch pin
- Shop: Curt Echo In-Line Bluetooth Brake Controller w/ OneControl App - Up to 4 Axles - Proportional
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness - Dash Knob - Up to 2 Axles - Proportional
- Shop: Curt TriFlex NEXT Trailer Brake Controller w/ Custom Harness - 1 to 4 Axles - Proportional
- Shop: Autowbrake Electric Brake Controller - Trailer Mount w/ Remote Fob - Up to 3 Axles - Proportional
- Shop: Suspension Enhancement
- Q&A: 2021 Ford Ranger XLT Wiring Harness with or without Power Wire
- Video: Draw-Tite Max-Frame Class IV Trailer Hitch DIY Installation - 2021 Ford Ranger
- Video: Review of the etrailer Ball Mount Kit for 2" Hitches
- Video: Install: Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector on a 2019 Ford Ranger
- Video: Curt Powered Tail Light Converter Installation - 2023 Kia Telluride
- Video: T-One Vehicle Wiring Harness with 7-Way Trailer Connector Spec Review
- Video: Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector Review
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
- Shop: Lift Assist
- Search Results: tonneau cover
- Search Results: tailgate assist
- Search Results: hitch adapters
- Search Results: prodigy brake controller
- Q&A: Recommended 7-Way Connector for a 2023 Ford Ranger
- Q&A: What is the Proper Gauge Wire for Installation of a Brake Controller and Trailer Brakes
- Search Results: curt echo button
- Q&A: Recommended Hitch for a 2021 Ford Ranger Tremor
on Custom Fit Vehicle Wiring
Klayton K.
1/11/2025
I have the same problem, and I do have a good 30 amp fuse in slot 73? Any other suggestions?