Install Video for 2007 Ford F-150 Installing Brake Controller Using 7-Way Adapter

Question

Question:

I need a video to explain the install of these items

asked by: Jack S

0

Expert Reply:

I attached an install video that uses the 7-way adapter part # 37185 and a Tekonsha brake controller but it would be the same process as any Curt brake controller like the # C24VV since the wire colors are the same.

expert reply by: Jameson C

0

Answer 1

The Curt TriFlex Trailer Brake Controller #C24VV with Wiring Adapter #C51436 is a very good option for your 2009 Ford F-150, though to mount it you will need to use the included mounting bracket and screw it in under the dash. If you (understandably)…

view full answer...

Answer 2

Hey John! So long as your 2010 F-150 came with either a 4-way connector or 7-way connector from the factory you can use the Curt Custom Wiring Adapter item #C51436 to install the Curt TriFlex NEXT Trailer Brake Controller item #C24VV. The plug in…

view full answer...

Answer 3

To install the Curt Discovery Trailer Brake Controller #C84VV on your 2005 Ford F-150 you will need the Curt Custom Wiring Adapter #C51322. This connector will be found under the dash on your driver side. I have attached a video of this adapter being…

view full answer...

Answer 4

For your 2008 Ford F-150 the Curt hitch part #C14360 is a confirmed fit and would be a great option. To install a brake controller in your 2008 Ford F-150 you would be able to use the brake controller port under the dash and you will need to complete…

view full answer...

Answer 5

Hey Christa, so the Curt Triflex part #C24VV shouldn't be draining your battery since it should be going into a sleep mode when not in use. To cut power to it you would need to unplug it at the rear of the controller. There isn't a master…

view full answer...

Answer 6

The correct brake controller install harness you need for your Triflex part #C24VV to install in your 2017 Ford F-150 is the #C51436.

view full answer...

Answer 7

The Hopkins Agility Trailer Brake Controller part 47295 and the Curt TriFlex Trailer Brake Controller part #C24VV are both fine options and very similar in their proportional design. That said, I recommend the Curt TriFlex because it's physically…

view full answer...

Answer 8

Hello Randy. The issue you are describing sounds like either a short on the brake wire on your 7-way, or a ground issue. The first thing to do is check the ground on your 7-way and make sure it is grounded to a good clean metal surface. Next check…

view full answer...

Answer 9

Because it's connected to a constant 12-volt power source, the LED you mention will remain illuminated after the vehicle is shut off. This is normal, and does not indicate a problem of any kind. After 15 or so minutes of inactivity, the brake…

view full answer...

Answer 10

The Curt brake controller install harness part #C51322 that you referenced is a confirmed fit for your 2007 Ford F-150.This adapter plugs into the port on your vehicle's built-in brake control wiring harness. For most applications, this harness…

view full answer...

Answer 11

On your 2005 Ford F-150 with the towing package, there will be a port under the dash that the Curt Custom Wiring Adapter, part #C51322 plugs into. I have attached a photo that has a red arrow pointing to the location on your truck. The Curt Venturer…

view full answer...

Answer 12

Hello Dan, I can definitely help with this. It is completely normal for the Curt TriFlex brake Controller #C24VV to show the current gain setting when the brakes are applied, or when the manual override is pressed. It sounds like you have the gain…

view full answer...

Install Video for 2007 Ford F-150 Installing Brake Controller Using 7-Way Adapter

Products Featured in This Question

Continue Researching