Brake Controller Install Harness for Curt Triflex to Install In 2017 Ford F-150

Question

Question:

I purchased Item # C24VV for a 2010 Mitsubishi Outlander, and now will be installing it on my F150. So what I am looking for is the adapter to use it on my F150.

asked by: Jerrod

0

Expert Reply:

The correct brake controller install harness you need for your Triflex part # C24VV to install in your 2017 Ford F-150 is the # C51436.

expert reply by: Jameson C

0

Answer 1

Because it's connected to a constant 12-volt power source, the LED you mention will remain illuminated after the vehicle is shut off. This is normal, and does not indicate a problem of any kind. After 15 or so minutes of inactivity, the brake…

view full answer...

Answer 2

Hello Randy. The issue you are describing sounds like either a short on the brake wire on your 7-way, or a ground issue. The first thing to do is check the ground on your 7-way and make sure it is grounded to a good clean metal surface. Next check…

view full answer...

Answer 3

The Curt TriFlex Trailer Brake Controller #C24VV with Wiring Adapter #C51436 is a very good option for your 2009 Ford F-150, though to mount it you will need to use the included mounting bracket and screw it in under the dash. If you (understandably)…

view full answer...

Answer 4

What you need to install the Curt Venturer #C74VV on your 2001 Ford F-150 is Wiring Adapter #C51322. I also added a link to a help article on installing a brake controller in a Ford truck which I highly recommend you take a look at.

view full answer...

Answer 5

To replace the existing trailer brake controller on your 2009 Ford F-150 with a Curt proportional unit, such as the Curt TriFlex #C24VV, you can indeed use the same Plug-In Adapter part #C51436 that you used before. You will just need to unplug your…

view full answer...

Answer 6

Hey John! So long as your 2010 F-150 came with either a 4-way connector or 7-way connector from the factory you can use the Curt Custom Wiring Adapter item #C51436 to install the Curt TriFlex NEXT Trailer Brake Controller item #C24VV. The plug in…

view full answer...

Answer 7

On your Curt TriFlex Trailer Brake Controller #C24VV, the decimal point as you put it is standby mode with no trailer connected. The blank screen is also standby mode and that screen is what is seen when simply starting the vehicle, but that screen…

view full answer...

Answer 8

The Curt brake controller install harness part #C51322 that you referenced is a confirmed fit for your 2007 Ford F-150.This adapter plugs into the port on your vehicle's built-in brake control wiring harness. For most applications, this harness…

view full answer...

Answer 9

A brake controller, whether it is a Curt or a Tekonsha or another brand, will plug into the same place on your 2014 Ford F-150. So I have included a link to a video showing installation of a different brake controller on a 2013 Ford F-150 and the…

view full answer...

Answer 10

To install the Curt Discovery Trailer Brake Controller #C84VV on your 2005 Ford F-150 you will need the Curt Custom Wiring Adapter #C51322. This connector will be found under the dash on your driver side. I have attached a video of this adapter being…

view full answer...

Answer 11

Hey Christa, so the Curt Triflex part #C24VV shouldn't be draining your battery since it should be going into a sleep mode when not in use. To cut power to it you would need to unplug it at the rear of the controller. There isn't a master…

view full answer...

Answer 12

For your 2008 Ford F-150 the Curt hitch part #C14360 is a confirmed fit and would be a great option. To install a brake controller in your 2008 Ford F-150 you would be able to use the brake controller port under the dash and you will need to complete…

view full answer...

Brake Controller Install Harness for Curt Triflex to Install In 2017 Ford F-150

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching