Slide Out Motor Replacement for Power Gear Motor # 1010000683

Question

Question:

I have a 2008 Fleetwood Fiesta that has a Power Gear motor and gear box P/N: 1010000683. I purchased a Klauber motor and gear box Model # K 01531A300P. The mounting bracket from the power gear motor does not line up with the Klauber motor. Is a bracket available andI also need the pin.

asked by: Bernie H

0

Expert Reply:

Based on the part number you mentioned the correct replacement motor is actually the part # LC67JJ.

expert reply by: Jameson C

0

Answer 1

Generators do not typically have a 12 volt power converter, so I recommend using the Battery Charger and Maintainer #CTEK56353 and splicing the connector that would go to the battery terminals into a 7-way connector like #30717. You will connect the…

view full answer...

Answer 2

You will need to measure to determine how long the fifth-wheel to gooseneck adapter will need to be. Park your fifth-wheel trailer on a fairly level surface. Back your vehicle under the fifth-wheel trailer stopping when the center of the king pin is…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Slide Out Motor Replacement for Power Gear Motor # 1010000683

Product Page this Question was Asked From

Continue Researching