Which Timbren is Best Choice for 2019 Ford E-Series Cutaway

Question

Question:

In your video above it is stated that the Timbren 350 have 2,000-lb capacity. However, in the product description it’s stated 3,000-lb. Furthermore, for the Timbren 350UH heavy duty, its capacity is 6,000-lb. What I really like to know is which kit will provide my 2019 E-350 Cutaway SRW 22’ long, with the most comfortable ride. My van is being used as a mobile home and is quite heavy in the middle to the rear. Thanks.

asked by: Ben

0

Expert Reply:

Unfortunately the most comfortable ride can be subjective. My suggestion is that if at present time you have hard contact with factory axle bump stops on frame and a very rough or unstable ride in turns, I would definitely select the Timbren Front Suspension Enhancement System, # TFEF350UH. If the current ride does not typically "bottom out" except for very rougher patches of road, then I would select the Timbren Front Suspension Enhancement System, # TFEF350.

expert reply by: Michael R

0

Answer 1

Hello again Rich; the higher rated #SSF-106-47 would be the better choice. However, since you really have this thing loaded and it is a work truck I recommend going with the Timbren SES #TFEF350UH. These have a capacity of 6,000 lbs so they can…

view full answer...

Answer 2

For a 2011 Ford E-350 Cube Van you would need the Timbren Front Suspension Enhancement System #TFEF350UH (approximately 4-7/8" tall) and the Timbren Rear Suspension Enhancement System #TFER35092LB (approximately 6-1/8" tall).

view full answer...

Answer 3

The Timbren Front Suspension Enhancement System part #TFEF350 is rated at 3,000 lbs and the Timbren Front Suspension Enhancement System part #TFEF350UH is rated at 6,000 lbs. I was able to call the manufacturer to confirm this. They will both fit…

view full answer...

Answer 4

I do have an option to get you more lift but the Lippert Axle Riser Kit part #LC382741 will not work on a Dexter Torflex Axle so you will need to use the Dexter Axle Riser Kit part #K71-707-02 if this is the route that you choose. The torsion axle…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Which Timbren is Best Choice for 2019 Ford E-Series Cutaway

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching