Recommended Timbren Suspension Enhancement For A 2011 Ford E-350 Cube Van

Question

Question:

Hi i have a ford e 350 2011 v8 5.4 single wheel commercial work 13 feet cube its a service truck with a lot of tools, gas welder, gas air compressor, part and oil. What timbren do you suggest me for the front and the rear? and what are the overall height of the two kit? Thanks

asked by: Jeffrey W

0

Expert Reply:

For a 2011 Ford E-350 Cube Van you would need the Timbren Front Suspension Enhancement System # TFEF350UH (approximately 4-7/8" tall) and the Timbren Rear Suspension Enhancement System # TFER35092LB (approximately 6-1/8" tall).

expert reply by: Kevin C

0

2011 Ford E-350 Cube Van
(click to enlarge)

Answer 1

The Timbren Front Suspension Enhancement System part #TFEF350 is rated at 3,000 lbs and the Timbren Front Suspension Enhancement System part #TFEF350UH is rated at 6,000 lbs. I was able to call the manufacturer to confirm this. They will both fit…

view full answer...

Answer 2

Hello again Rich; the higher rated #SSF-106-47 would be the better choice. However, since you really have this thing loaded and it is a work truck I recommend going with the Timbren SES #TFEF350UH. These have a capacity of 6,000 lbs so they can…

view full answer...

Answer 3

Unfortunately the most comfortable ride can be subjective. My suggestion is that if at present time you have hard contact with factory axle bump stops on frame and a very rough or unstable ride in turns, I would definitely select the Timbren Front…

view full answer...

Answer 4

I do have an option to get you more lift but the Lippert Axle Riser Kit part #LC382741 will not work on a Dexter Torflex Axle so you will need to use the Dexter Axle Riser Kit part #K71-707-02 if this is the route that you choose. The torsion axle…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hi Cindy! The Lets Go Aero MoonUnit Tailgate Tent - 10" x 8" x 7-1/2" - RV Van Edition #LGA74ZR can indeed be left free-standing if you need to drive off somewhere. It does not need to be attached to your vehicle at all times, which is…

view full answer...

Recommended Timbren Suspension Enhancement For A 2011 Ford E-350 Cube Van

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching