How to Get Wires Through The Lippert Double Flexguard RV Slide-Out Kits Brackets
Updated 07/19/2021 | Published 07/15/2021 >
Question:
How do you get the wires through the the brackets on the Lippert flex guard double kit
asked by: Ronald P
Expert Reply:
The black flex guard will slide through the longer thin hole on the brackets. There is no notch to slide your wires in, so your wires will need to be disconnected on one side or the other to feed them through the holes on the brackets.
I have attached photos of the installation instructions for the Lippert Double Flexguard RV Slide-Out Kit Hardware # LC1346281.
Installation Instructions are as follows.
1. Position Flex Guard under the slide-out room where the wiring or hoses to be protected are located.
2. Insert the aluminum pin (Fig. 1A) into the Flex Guard (Fig. 1B) with the mounting bracket (Fig. 1C)
facing up. Slide the star washer (Fig. 1D) over the end of the pin at the bottom of the Flex Guard and
push in place.
3. Slide the Flex Guard clips (Fig. 1E) onto the end of the Flex Guard with the holes in the clips facing the
direction of the hoses and wiring to hold them in place. Space all clips evenly throughout the length of
the Flex Guard.
4. Install Flex Guard mounting bracket (Fig. 1C) to the bottom of the unit floor, perpendicular to the
outrigger and furthest away from the I-beam or room bar, using four #10 x 1" self-tapping screws or
#10 x 1" wood screws (Fig. 2A).
5. Mount the flat end of the Flex Guard to the LCI-supplied mounting plate (Fig. 3A) mounted offset to
the aluminum pin (Fig. 1A) at the opposite end using two #10 x 1" self-tapping screws (Fig. 3B) per belt
section. Install the LCI-supplied mounting plate to the bottom side of the slide-out room.
6. Slide any hoses and wiring through the holes in the Flex Guard clips when installing in order to protect
hoses and wiring with the Flex Guard.
7. Flex Guard should be kept parallel to the slide room floor.
8. Make sure the flat end of the Flex Guard is mounted several inches away from the direction of the bend
of the retracted Flex Guard (Fig. 4).
Product Page this Question was Asked From
Lippert Double Flexguard RV Slide-Out Kit Hardware
- RV Slide Out Parts
- Hardware
- Flexguard
- Lippert
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Lippert Double Flexguard RV Slide-Out Kit Hardware
- Video: Breaking Down the Lippert Components Single Flexguard RV Slide-Out Kit Hardware
- Shop: Kenda Karrier S-Trail ST145/R12 Radial Tire w/ 12" White Spoke Wheel - 5 on 4-1/2 - LR D
- Shop: Lippert Triple Flexguard RV Slide-Out Kit Hardware
- Search Results: trailer tire
- Search Results: trailer tires and wheels
- Shop: Dexter Trailer Hub and Drum for 8,000-lb E-Z Lube Axles - 12-1/4" Diameter - 8 on 6-1/2
- Shop: Lippert Components Single Flexguard RV Slide-Out Kit Hardware
- Q&A: Installation of Lippert Components Universal Slide Out Wear Pads
- Shop: Rambler ST145/R12 Radial Trailer Tire - Load Range D
- Shop: Karrier KR35 ST175/80R13 Radial Trailer Tire - Load Range C
- Shop: Tonneau Cover
- Video: Review of MORryde Replacement number 5 Rubber Shear Spring - MR85UR
- Q&A: Installation of Lippert Flexguard RV Slide-Out Kit Hardware
- Video: Lippert Double Flexguard RV Slide-Out Kit Hardware Installation - 2007 Starcraft Homestead Lite Fift
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Shop: Suspension Enhancement
- Q&A: Which is Better for Highway Use 4.80-12 or 5.30-12 Trailer TIres
- Search Results: trailer wiring
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Brake Controller
- Search Results: trailer jack




